Samsung TXN2771HF/TXN3071WHF Remote Control ¿ TV/Component, ¸ DNIe, ˛ VCR Controls, PIP Controls

Page 13

Y O U R N E W T V

Remote Control

¿TV/Component

Press to switch the TV, COMPO- NENT1, 2, or DIGITAL mode.

Note: The DIGITAL mode does work in TXN2798HF/ TXN3098WHF/ TXN3298HF models.

¸DNIe

(TXN3298HF/TXN3098WHF/

TXN2798HF)

Activates DNIe (Digital Natural Image engine).

˛VCR Controls

REW (Rewind)

Press to rewind a tape in your VCR.

STOP

Press this button to stop a tape during play, record, rewind or fast forward. If the button is pressed during Full-Automatic play, the function will be can- celled.

PLAY/PAUSE

Press the PLAY/PAUSE button to play back prerecorded tapes or pause the tape.

FF

Press to fast forward the tape in your VCR.

◊SET

Use this button when you are set- ting up your remote control to operate your Set Top Box, VCR, Cable box, or DVD.

±

≠

–

STILL (Main picture)

Press to stop the action during a particular scene. Press again to resume normal video.

Note: The still function doesn’t operate in Component 1, 2 mode.

PIP Controls

(TXN3298HF/TXN3098WHF/

TXN2798HF)

PIP ON

Press this button to control the PIP window.

SIZE

Press to make the PIP window small, large, double screen or stock ticker window.

SWAP

Exchanges the video signal that is currently displayed on the main screen with the signal in the PIP window.

CH

Displays the available channels in sequence (These buttons change channels in the PIP window only).

Reset

If your remote control is not func- tioning properly, take out the bat- teries and press the reset button for about 2~3 seconds. Re-insert the batteries and try using the remote control again.

13

Image 13

Contents AA68-02942A-00 Owner’s InstructionsAs an Energy Star Partner Thank You for Choosing Samsung Example Antenna Grounding Page Your New TV InstallationOperation Troubleshooting Special FeaturesAppendix Chapter One List of FeaturesFront Panel Buttons Familiarizing Yourself with The TVVOL , + Remote Control Sensor Standby indicator¨ CH and CH Side Panel Jacks∏ VHF/UHF jack Rear Panel JacksOutput jacks Output jackMode Remote Control¨ Number buttons +100Reset Remote Control ¿ TV/Component¸ DNIe ˛ VCR ControlsAntennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasAntennas with 75-ohm Round Leads Connecting Cable TVSeparate VHF and UHF Antennas Cable without a Cable BoxConnecting to a Cable Box that Descrambles Some Channels Connecting to a Cable Box that Descrambles All ChannelsConnect this cable to a two-way splitter Install AT I O N Unplug the cable or antenna from the back of the TV Connecting a VCRConnecting an S-VHS VCR Make sure the jacks you are using are underneath the numberConnecting a Second VCR to Record from the TV Connecting a DVD Player 480i/480pConnecting to Y,Pb,Pr Connecting a Digital TV Set-Top Box 480p/1080iInstall AT I O N Connecting a Camcorder Installing Batteries in the Remote Control Press the Power button on the remote control Plug & Play FeatureTurning the TV On and Off Message Plug & Play is displayedSelect the Setup menu and press the Enter button If you want to reset this featureViewing the Menus Viewing the Menus and On-Screen DisplaysViewing the Display Selecting a Menu Language Memorizing the Channels Selecting the Video Signal-sourcePress the Menu button to display the menu Storing Channels in Memory Automatic Method Press the Menu button Adding and Erasing Channels Manual MethodChanging Channels Adjusting the VolumeButton to select Channel Labeling the ChannelsOption 1 Setting the Clock Manually Setting the ClockOr button repeatedly until the correct hour appears E R AT I O N E R AT I O N √ button increases it Press the Menu button to exit Customizing the PictureUsing Automatic Picture Settings TXN2798HF/ TXN3098WHF/ TXN3298HF models Customizing the SoundUsing Automatic Sound Settings Viewing an External Signal Source Setting Up Your Remote Control to Operate Your VCR or DVD Customizing Your Remote ControlDVD Codes VCR CodesCable Box Setting Up Your Remote Control to Operate Your Cable BoxCodes Press the button to select Fine tune Fine Tuning ChannelsPress the button to select LNA LNA Low Noise Amplifier TXN2798HF/TXN3098WHF/TXN3298HFPress the button to select Tilt TiltDNIeTM Digital Natural Image engine Press button to select Digital NR Digital Noise ReductionTXN3271HF/TXM2771HF/TXN3298HF/TXN2798HF/TXN3275HF Changing the Screen SizePress the P.SIZE button to change the screen Changing the Color Tone Freezing the Picture Using the R.Surf FeatureWhen finished, press Menu button Setting the On/Off TimerSetting the Sleep Timer Choosing a Multi-Channel Sound MTS Soundtrack Auto Volume Surround Melody Viewing Closed Captions Activating Picture-in-Picture Viewing Picture-in-Picture TXN2798HF/TXN3098WHF/TXN3298HFTV, AV1, AV2 and AV3 Press the Menu button to exit Selecting a Signal Source External A/V for PIPChanging the Size of the PIP Window Swapping the Contents of the PIP image and Main image Changing the PIP Channel Setting Up Your Personal ID Number PIN Using the V-Chip USADigits for your PIN and enter them How to Set up Restrictions Using the TV guidelines How to Enable/Disable the V-ChipParent Guidance General audienceTV-14 Mature audienceEnter Pin screen will appear. Enter your 4-digit PIN number E C I a L F E AT U R E S Using the V-Chip Canada How to Enable/Disable the V-Chip TV-G Enter Pin screen will appear. Enter your 4-digit PIN number Appear. Enter your 4-digit PIN number How to Set up Restrictions Using the Canadian EnglishProgramming intended for children under age How to Set up Restrictions Using Canadian FrenchEnter Pin screen will appear. Enter your 4-digit PIN number Talk shows, music videos, and variety programming TXN2798HF/TXN3098WHF/TXN3298HF Viewing the DemonstrationChapter Five Identifying ProblemsUsing Your TV in Another Country Cleaning and Maintaining Your TVSpecifications M O