Memorizing the Channels
Your PDP can memorize and store all of the available channels for both
and cable channels. After the available channels are memorized, use the CH 
and CH 
buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the PDP (i.e., an antenna or a cable system).
Storing Channels in Memory (Automatic Method)
First, select the correct signal source (Air, STD, HRC |
|
|
| Channel |
1 and IRC). See steps on previous page. |
| Air / CATV | : | Air √ |
| ||||
Press the MENU button. Press the ▲ or ▼ button to |
| Auto Program |
| √ |
select “Channel”, then press the ENTER button. |
|
| ||
| Add / Delete |
| √ | |
|
| |||
|
| Fine Tune |
| √ |
|
|
|
| √ |
Press the MENU button. Press the ▲ or ▼ button to
1 select “Channel”, then press the ENTER button.
Channel
Air / CATV | : Air √ |
Auto Program | √ |
Add / Delete | √ |
Fine Tune | √ |
LNA | : | On |
Ch.Scan |
| √ |
Move | Enter | Return |
2 Press the ENTER button to select “Air/CATV”.
| LNA | : |
| On √ |
| ||
| Ch.Scan |
|
|
|
| √ |
|
|
|
|
| ||||
|
|
|
| ||||
|
|
|
|
|
|
|
|
| Move | Enter | Return |
| |||
|
|
|
|
|
|
|
|
|
|
|
| Channel |
| ||
| Air / CATV | : |
|
|
|
|
|
|
|
|
|
|
| ||
|
| Air |
| ||||
| Auto Program |
| STD |
|
| ||
| Add / Delete |
| HRC |
|
| ||
|
| ||||||
| Fine Tune |
|
| IRC |
|
| |
| LNA | : |
| On |
| ||
| Ch.Scan |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Move | Enter | Return |
| |||
Press the ▲ or ▼ button to select “Auto Program”,
2 then press the ENTER button.
➤Quick way to access the Automatic Channel Setting: Just press the “AUTO PROG.” button on the remote control.
The PDP will begin memorizing all of the available
3 channels.
After all the available channels are stored, the Auto program menu reappears. Press the MENU button to stop.
Channel
| Air / CATV | : | Air | √ | |
| Auto Program |
|
| √ | |
| Add / Delete |
|
| √ | |
|
|
| |||
| Fine Tune |
|
| √ | |
| LNA |
| : | On | √ |
| Ch.Scan |
|
|
| √ |
|
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
Move | Enter |
| Return | ||
Auto Program
Air 28
Press the ▲ or ▼ button to select “Air”, “STD”,
3 “HRC” or “IRC”.
•If you are connected to an antenna, leave “Air” displayed. If you connected cable, press the
▲ or ▼ button to the display the type of cable system: “STD”, “HRC” or “IRC”.
(If you are not sure which type of cable system you have, contact your cable company).
4 Press the MENU button to exit.
Note
|
|
|
| Channel | ||
| Air / CATV | : |
|
|
|
|
|
| Air | ||||
| Auto Program |
| STD |
| ||
| Add / Delete |
| HRC |
| ||
| ||||||
| Fine Tune |
|
| IRC |
| |
| LNA | : |
| On | ||
| Ch.Scan |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Move | Enter | Return | |||
Return
Note
•The PDP automatically cycles through all of the available channels and stores them in memory. This takes about one to two minutes.
•STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (Next page).
32
33