Samsung HPM5027 manual How to Set up Your Display Setting Windows only, Ibm Pc / At

How to Set up Your Display Setting (Windows only)

Notes:

The plasma panel of this monitor is composed 1366 pixels & 768 lines. That is, the best resolution of this monitor is 1366 X 768.

Thus, select 1366 X 768 resolution in same way as below when you control the display setting, If your video card does not support 1366 X 768 resoution, the resolution of 1024 X 768 is recommended. If you select one of resolutions above, you can use this monitor in best condition.

The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.

On the windows screen, select in the following sequence : Start ➝ Settings ➝ Control Panel.

When the control panel screen appears, click on “Display” and a display dialog-box will appear.

Select the “Settings” tab in the display dialog-box.

The two key variables that apply the PDP-PC inter- face are “resolution” and “colors.” The correct set- tings for these two variables are:

• Size (sometimes called “resolution”): 1024 x 768 pixels.

• Color: “24-bit” color (might also be expressed as “16 million colors”)Shown at left is a typical screen for “Display” dialog box.

If a vertical-frequency option exists on your dis- play settings dialog box, the correct value is “60” or “60 Hz.” Otherwise, just click “OK” and exit the dialog box.

44 Continued...

Notes:

Both screen position and size will vary, depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported:

Video signal	Dot X Line		Vertical	Horizontal	Vertical	Horizontal
			Frequency (Hz)	Frequency (kHz)	polarity	polarity
	640	X 350	70.086	31.469	N	P
			85.080	37.861	N	P
	640	X 400	85.080	37.861	P	N
	720	X 400	70.087	31.469	P	N
			85.039	37.927	P	N
	640	X 480	59.940	31.469	N	N
			72.809	37.861	N	N
IBM PC / AT			75.000	37.500	N	N
Compatibler
			85.008	43.269	N	N
	848	X 480	60.000	29.838	P	N
			72.000	35.156	P	N
			75.000	36.072	P	N
			85.000	37.650	P	N
	800	X 600	56.250	42.925	N/P	N/P
			60.317	37.879	P	P
			72.188	48.077	P	P
			75.000	46.875	P	P
			85.061	53.674	P	P
	1024 X 768		60.004	48.363	N	N
			70.069	56.476	N	N
			75.029	60.023	P	P
			84.997	68.677	P	P
	1152 X 864		75.000	67.500	P	P
	1280 X 768		60.000	47.700	P	N
	(W-XGA)
			75.000	60.150	P	N
	1280	X 1024	60.020	63.981	P	P
			75.025	79.976	P	P
	1366	X 768*	60.000	48.200	N	N

(N: Negative / P: Positive)

•The PDP might operate abnormally if a non-standard video format is selected.

•When this PDP is used as a PC display, 24-bit color is supported (over 16 million colors).

•Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows).

Check your PC instruction book for information about connecting your PC to a PDP.

•If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHz (horizontal).

•In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the Source button to enter the VIDEO mode. Also, make sure that the PC is connected.

•Connect only a PC monitor to the monitor output port while viewing the PC screen. (Otherwise, random signals might appear).

*This mode is only supported by a particular video card(PIXEL PERFECT made by IMAGINE

GRAPHICS Ltd.). 45