Samsung BN68-01415A-00 user manual Check Points before Requesting Service, Symptom Solution

Page 44

Check Points before Requesting Service

Symptom

Solution

Anynet+ does not

■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+

work.

devices only.

 

■ Connect only one receiver.

 

■ Check if the Anynet+ device power cord is properly connected.

 

■ Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections.

 

■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

 

■ Check whether the TV remote control is in TV mode.

 

■ Check whether it is Anynet+ exclusive remote control.

 

■ Anynet+ doesn’t work at a certain condition. (Searching channels, Operating

 

WISELINK, Plug & Play, etc.)

 

■ When connecting or removing the HDMI 1.3 cable, please make sure to search

 

devices again or restart your TV.

 

■ Check if the Anynet+ Function of Anynet+ device is set on.

I want to start

■ Check if the Anynet+ device is properly connected to the TV and check if the

Anynet+.

Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu.

 

■ Press the TV button on the TV remote control to switch to TV. Then press the

 

TOOLS button to show the Anynet+ menu and select a menu you want.

I want to exit Anynet+. ■ Select View TV in Anynet+ menu.

■Press the SOURCE button on the TV remote control and select a device other than Anynet+ devices.

■Press any of P/, CH LIST, PRE-CH, and such to change to the

TV mode. (Note that the channel button operates only when a tuner-embedded Anynet+ device is not connected.)

The Configuring

■ You cannot use the remote control when you are configuring Anynet+ or

Anynet+ connection

switching to a view mode.

message appears on

■ Use the remote control when the Anynet+ setting or switching to view mode is

the screen.

complete.

The Anynet+ device

You cannot use the play function when Plug & Play is in progress.

does not play.

 

The connected device

■ Check whether or not the device supports Anynet+ functions.

is not displayed.

■ Check whether or not the HDMI 1.3 cable is properly connected.

 

■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

 

■ Search Anynet+ devices again.

 

■ You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI

 

cables may not support Anynet+ functions.

 

■ If it is terminated by an abnormal situation such as disconnecting the HDMI 1.3

 

cable or power cord or a power failure, please repeat the device scan.

The TV programme

Check whether the antenna jack on the recording device is properly connected.

cannot be recorded.

 

English - 42

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Country Customer Care Centre Web Site Precautions When Displaying a Still Image Contents Installing the Stand Installing the Wall Mount KitOwner’s Instructions Warranty card List of PartsViewing the Control Panel Connecting External A/V Devices AV Viewing the Connection PanelPC in PC / Audio Connect to the video and audio output jack on your PCKensington Lock depending on the model Headphones jackVideo or Video / R-AUDIO-L Teletext Functions Viewing the Remote ControlDisplays the main on- screen menu Installing Batteries in the Remote Control Switching On and OffPlacing Your Television in Standby Mode Mains lead is attached to the rear of your setPress the or button to select a menu Using the Tools ButtonViewing the Menus Press the Power button on the remote control Plug & PlayIf you want to reset this feature Storing Channels AutomaticallyChannel mode Storing Channels ManuallyColour System Auto/PAL/SECAM/NTSC4.43/NTSC3.58 Press the or button to select the required colour standardAdding / Locking Channels Adding channelsSorting the Stored Channels Assigning Channels NamesEnter button Press the or button to select Sort, then press ThenFine Tuning Channel Reception Press the Enter button again, to select Mode Easy SettingChanging the Picture Standard Press the Exit or Tools button to exitAdjusting the Custom Picture Configuring Detailed Settings on the PictureYou can set detailed picture settings Black Adjust Off/Low/Medium/HighResetting the Picture Settings to the Factory Defaults Size 169/Wide Zoom/Zoom/43/Just Scan Configuring Picture OptionEnter Blue Only Mode Off/On Digital NR Off/Low/Medium/High/AutoDNIe Off/ Demo/On Hdmi Black Level Normal/LowViewing the Picture In Picture PIP Sound Features Mode Standard/Music/Movie/Speech/CustomAuto Volume Off/On SRS TS XT Off/OnSelecting the Sound Mode Connecting Headphones Sold separatelySetting and Displaying the Current Time Setting the Sleep TimerPress Enter buttonChoosing Your Language Switching the Television On and Off AutomaticallyAuto Power Off TV power on/off melody sound can be adjusted Melody / Entertainment / Energy SavingMelody Off/Low/Medium/High Melody does not playEnergy Saving Off/Low/Medium/High/Auto High or Auto Press the Exit or Tools button to exitSelecting the Source Editing the Input Source NamesSetting up Your PC Software Based on Windows XP Display ModesSub Input HDMI/DVI InputSetting up the TV with your PC Press the Source button to select PC modeAuto Adjustment Image ResetUsing the Wiselink Function Using the Wiselink Menu Using the Remote Control Button in Wiselink Menu OperationsInput, then press the Enter button Memory Device, then press the Enter buttonUsing the Photo Jpeg List Viewing a Slide ShowUsing the Menu during a Slide Show Slide Show Speed Such as the resolution File Size Date modifiedList Folder icon Photo iconUsing the Option Menu Start Slide ShowZoom RotateUsing the MP3 List Using the Option Menu PlayRepeat Music Music function information iconUsing the Setup Menu Background Music SettingBackground Music Screen SaverTo connect to Home Theater What is Anynet+?Connecting Anynet+ Devices Setting Up Anynet+ Scanning and Switching between Anynet+ Devices Select Setup, then press the Enter buttonSetup Select DeviceRecord Menu on DeviceYou can make a recording of a TV programme using a recorder RecordingListening through a Receiver Press the Tools button. Then Press the Enter button toCheck Points before Requesting Service Symptom SolutionTeletext Feature English Adjust to the desired position using the ,,, buttons Auto Wall-Mount Sold separatelyEntering the menu Remembering the PositionUsing the Anti-Theft Kensington Lock depending on the model Moving to the remembered positionTroubleshooting Before Contacting Service Personnel Technical and Environmental Specifications This page is intentionally Left blank
Top Page Image Contents