Samsung LTN325W manual Connecting a VCR

Page 19

venus-02-en 6/28/03 8:14 AM Page 11

IN S TA L L AT I O N

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 7-10).

Skip step 1 if you have not yet connected to an antenna or a cable system.

1

Unplug the cable or antenna from the back of the TV.

2

Connect the cable or antenna to the ANTENNA IN terminal on the back of the VCR.

3

Connect a coaxial cable between the

ANTENNA OUT terminal on the VCR and the antenna terminal on the TV.

A coaxial cable is usually included with a VCR. (If not, check your local electronics store).

4

Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO jacks on the TV.

If you have a “mono” (non-stereo) VCR, use the Y-connector (not supplied) to hook up to the left and right audio input jacks of the TV. If your VCR is stereo, you must connect two cables.

5

Connect a video cable between the VIDEO OUT jack on the VCR and the VIDEO jack on the TV.

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

# Each external input source device has a different back panel configuration.

English-11

Image 19

Contents Owner’s Instructions Safety Instructions BN68-00448A-03Eng01 10/6/03 1103 AM FCC Information BN68-00448A-03Eng01 10/6/03 1103 AM Memo Operation InstallationSpecial Features Your New TVPC Display TroubleshootingAppendix List of Parts List of FeaturesFront Panel Buttons Familiarizing Yourself with Your New TVVOL + Rear Panel Jacks CH and CH Channel Up/Down Remote ControlVOL + and VOL DNIe Button +100Remote control doesn’t work Installing Batteries in the Remote ControlAntennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasCable without a Cable Box Connecting Cable TVAntennas with 75-ohm Round Leads Separate VHF and UHF AntennasConnecting to a Cable Box that Descrambles Some Channels Connecting to a Cable Box that Descrambles All ChannelsEnglish-10 Connecting a VCR Connecting an External Input Source Connecting an S-VHS VCRConnecting a Digital TV Set-Top Box Connecting a DVD PlayerHow to Connect Connecting the SpeakersHow to Turn the Sound On SUB Connecting a PCTurning the TV On and Off Adjusting the VolumeUsing the Channel Buttons Using the PRE-CH Button to select the Previous ChannelViewing the Display Using MuteViewing the Menus Setting Up the Remote to Operate Your VCR Setting Up Your Remote ControlSetting Up the Remote to Operate Your Cable Box Setting Up the Remote to Operate Your DVD Remote Control Codes Chapter Four Plug & Play FeatureMemorizing the Channels Selecting the Video Signal-sourceTo select channels over Storing Channels in Memory Automatic MethodAdding and Erasing Channels Manual Method To Select TV/InputTo Edit the Input Source Name Alternate method Using Automatic Picture SettingsCustomizing the Picture Using Automatic Sound Settings Customizing the Sound Selecting a Menu Language Setting the Blue Screen Mode To Select an External Output Device LNA Low Noise Amplifier Fine Tuning Channels Viewing Picture-in-Picture PIP SettingsActivating Picture-in-Picture Changing the PIP Channel Swapping the Contents of the PIP and Main imageChanging the Size of the PIP Window Freezing the Picture Changing the Screen SizeAdjusting the Background Color Setting the DNIe Turning the Dolby Pro-Logic II On To Enjoy Dolby Digital SoundTurning the Dynamic Range On Speaker Speaker SettingsLevel Time Delay Trademark & Label License Notice Changing the Stereo Settings Selecting the Main or Sub Sound You can select either Main or Sub when PIP is OnTo Select an External Input Device Adjusting the Headphone Sound Setting the Clock Setting the On/Off Timer What is Absent Power Off? Setting the On/Off Timer Using the Menu Setting the Sleep TimerSetting Up Your Personal ID Number PIN Using the V-ChipHow to Set up Restrictions Using the ‘TV guidelines’ How to Enable/Disable the V-ChipTV-Y English-58 NC-17No children under age Adults only NR Not rated How to Set up Your PC Software Windows only Using Your TV as a Computer PC DisplayAdjusting the Screen Quality Changing the Screen Position To Initialize the Screen Settings Use to return the screen settings to the default valuesHow to DVI Select Choose the right DVI signal for your computerHow to Auto Adjust Chapter Six Identifying ProblemsEnglish-67 Maintenance of Your LCD TV Installing StandOptional Using the Anti-Theft Kensington LockList of Contents How to Attach the LCD TV to the Bracket Using Your TV in Another Country Cleaning and Maintaining Your TVPin Assignments LTN325W LTN406W SpecificationsDisplay Modes Clock Sync Polarity ModeFrequency KHz MHz

Related manuals

Manual 81 pages 50.35 Kb