Samsung LW-15E23C, LW-17E24C user manual Connecting Your LCD TV/Monitor, Connecting Computer ➀ ➁ ➂

Page 7

4E_body3p.fm Page 5 Wednesday, December 19, 2001 4:09 PM

Setting up Your LCD TV/Monitor

Connecting Your LCD TV/Monitor

DC

 

POWER VIDEO AUDIO(ST) SCART

 

V

I

D

 

E

O

S-

V

I

 

D

O

E

TV or VCR

 

Figure 2. Cable connections

1.Connecting Computer ( ➀ ➁ ➂ )

A.Connect the power cord to the DC Adaptor and connect the adaptor jack to the DC 14V power connector on the back of the TV/Monitor.

B.Connect the 15-pin D-SUB of the video signal cable to the PC video connector on the back of the TV/Monitor.

C.Connect the stereo audio cable to “Audio (ST)” on the back of the TV/Monitor and the other end to “ Audio Out” terminal of the sound card on your computer.

D.If necessary, please install TV/Monitor driver contained on the accompanied CD. For driver installation, please refer “Installing Video Driver” section on page 6.

2.Connecting External A/V Devices ( ➃ ➄ )

A.Connect RCA audio cables to “Audio (R)” and “Audio (L)” terminals and the other ends to corresponding audio out terminals on the A/V device.

(Stereo-RCA Cable not included)

B.Connect RCA (Yellow) or S-VHS cable to an appropriate external A/V device such as VCR, DVD or camcorder. (RCA cable and S-VHS cable not included)

C.Headphone may be connected to the headphone output on the right-hand side of the TV/Monitor ( ). While the headphone is connected, the sound from the built- in speakers will be disabled.

3.Connecting scart and TV/CATV ( ➆ ➇ )

A.Connect Scart Cable such as TV etc... (Scart cable not included)

B.Connect an antenna or CATV cable to the antenna terminal on the back of the TV/Monitor.

English 5

Image 7
Contents LW-15E23C LW-17E24C 1024 x For Better Display1280 x Table of Contents Risk of Electric Shock From the AC outlet before any serviceUnpacking Your TV/Monitor Tilt the screen Setting up an Ergonomic WorkstationConnecting scart and TV/CATV ➆ ➇ Connecting Your LCD TV/MonitorConnecting Computer ➀ ➁ ➂ Connecting External A/V Devices ➃ ➄Plug and Play Installing the Video DriverSelf-Test Feature Check Stfc Power IndicatorWarm-up Time Getting HelpUser Controls Automatic Save While you are watching full screen TV or in PIP mode Direct-Access FeaturesInitial OSD icons Once to activate the selected sub-menu Your adjustmentsFunction or to exit from the OSD Language OSD functions and adjustmentsSetting bar Tool TipColor PC functions and adjustmentsSetting bar Main menu Tool Tip ContrastImage Effect Sharper Sharpen more Medium Soften Soften more Handled in several different waysAlso be panned Pan Move the zoomed image horizontally Vertically ImageIn- Picture Position SoundAs DVD, VCR, TV or PC PictureOther than PC. DVD, VCR, TV TV/ Video functions and adjustmentsChange the colour PAL Secam SetupActive TimerArea By Remote-Control DUAL/ I/II Features that can only be accessed via remote controllerNicam MIX TV Mode Full TTX ModeMIX Mode TTX onScreen in Double Height HoldSize Double HeightState PowerSaverTroubleshooting Vertical frequency 56 Hz ~ 85 Hz Maximum refresh rate Power Saver,Installing the Video Driver Horizontal frequencyNo sound Troubleshooting Audio and TVCheck the volume control on Documentation Adjust the Treble and Bass toPAL/NTSC/SECAM SpecificationsCVBS, S-VHS Body DimensionsWeight TV/Monitor TemperatureDDC SCL Pin AssignmentsGND GND DDC SDADisplay Modes Preset timing modesAttaching a wall or Arm mounting device Refer to page 32 to fold the base Installing Vesa compliant mounting devicesRetractable Stand Maintenance of Your LCD TV/MonitorMenu AutoDUAL/I/II ExitUser Information User InstructionsDeclaration of conformity for products Marked with FCC Logo Printed on recyclable paper