Samsung 4240 manual Connecting External Devices to the PDP

Page 11

BN68-00597A-01 4/2/04 6:38 PM Page 11

Installing the Display on the Wall Attachment Panel (continued)

➢The exterior of the PDP may be different than the picture.

	(Assembly and installation of the plastic hanger is the same.)		ENG
1	Remove the screws from the back of the PDP. 2	Use the screws and assemble the plastic
		hanger.

3Tighten the screws of the plastic hanger to the back side of the PDP.

☛◆ Please ask the installers to install the wall mount bracket.

◆Please be sure to check if the plastic hanger is completely secured on both the left and right side after hanging the PDP on the wall mount bracket.

◆Please avoid catching your fingers while installing and adjusting the angle.

◆Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP.

4Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be separated from wall mount bracket.

PDP panel

Wall

Wall attachment panel bracket

ConnectingExternalDevicestothePDP

◆To connect external devices such as a DVD or a Home Theater System to the PDP, please refer to following instructions:

1Be sure to remove the safety pins underneath the PDP.

◆If the safety pins are not removed, the angle cannot be adjusted. Any attempt to do so may cause damage to the PDP.

2Pull out the bottom of the PDP (which has been attached to the Wall Mount Bracket) in the direction indicated by the arrows (refer to the illustration) until it clicks.

◆ Using the PDP After Connecting External Devices.

Be sure to secure the PDP by inserting the 2 safety pins after readjusting the angle of the PDP to 0o.

◆For safety, be sure to secure the PDP using the safety pins.

If the safety pins are not used, the PDP may fall, causing serious injury.

11

Image 11

Contents PDP-TELEVISION Height WarrantyScreen Image retention Cell DefectSold Separately Power CordOwner’s Instructions Contents Symbols Depending on your model Actual configuration on your PDP may be differentFor further details about connection, refer to pages 55~59 Depending on your modelInfrared Remote Control Angle of the PDP can be up to 20 degrees left/right Inserting the Batteries in the Remote ControlWall Mount Bracket Plastic Hanger Installing the Display on the Wall Attachment PanelConnecting External Devices to the PDP Use the 3M/5M/7M cable supplied by Samsung Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Rear of the PDPMains lead is attached to the rear of your PDP Switching On and OffDisplay the on-screen menu system Becoming Familiar with the Remote ControlRemote control is used mainly to Change channels and adjust the volumeSetting Up Your Remote Control To start the search, press the Enter button Plug & Play FeatureChoosing Your Language If you want to reset this featureSee Storing Channels AutomaticallyBG DK I L Storing ChannelsManuallyAuto PAL Secam or Auto NT3.58 NT4.43 PAL60 Channel mode Skipping unwanted channels Skipping Unwanted ChannelsSorting the Stored Channels Assigning Names to Channels Using the LNA Low Noise Amplifier Feature Activating the child lock Activating the Child LockDynamic Standard Movie Custom High Middle Low Custom Displaying InformationChanging the Picture Standard Colour Tone Cool2, Cool1, Normal, Warm1, Warm2 Adjusting the Picture SettingsCustom Options available in PC, DVI Mode Contrast Brightness, SharpnessCustom PC mode only Colour1 Colour2 Colour3 Adjusting the Picture Settings PC or DVI ModePreset to the PC mode by using the Source button Setting the Picture PC ModeSetting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneColour System and Sound System settings are correct Result Options available in the Channel group are Viewing the Channel Scan PictureFreezing the Current Picture Result Main menu is displayedSelecting the Picture Size Positioning and Sizing the screen using ZoomPC to DVI Mode DNIeTM Digital Natural Image engine Selecting the Film ModeSelect the option Off or On Setting the Blue ScreenSetting the Melody Sound Viewing the Picture In Picture PIP Table of PIP SettingsButton after changing the sub Easy functions of remote controlButtons Feature PictureUsing the Digital NR Digital Noise Reduction Feature Standard Music Movie Speech Custom Changing the Sound StandardAdjusting the Volume Automatically Adjusting the Sound SettingsStereo Setting the TruSurround XTSelecting the Internal Mute Selecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Absent Power Off Switching the Television On and Off AutomaticallySatellite STB, AV Receiver, DVD Receiver, Game Viewing an External Signal SourceAV1, AV2, AV3, S-Video1,S-Video2,Component1 Redirecting an Input to the External Output Contents Teletext FeaturePress the TTX/MIX button again Displaying the Teletext InformationTo display Press Selecting Display OptionsSelecting a Teletext TeleWeb Feature Option Opening the Home Using the TeleWeb Menu after Displaying the TeleWebBookmarking the current Entering the bookmarked URLTeleWeb Easy Accessing the TeleWeb Service via the Remote ControlInput Connecting to the External DevicesInput/Output Specification Rear of the TVRear of the TV Side of the TV Connecting to the S-Video InputConnecting to the PC Input Connecting to the DVI InputConnecting Additional Speakers Connecting to the Component InputTo Display the DVD Home Theater Connecting and Using the Home Theater SystemConnecting the Home Theater System This speaker installation guide is for the 4240 Model Installing the SpeakersHow to Assemble the Speakers Wall Mount Shown at left is a typical screen for Display dialog box Bit colourNVidia chipset Video Signal Dot x Line Vertical Horizontal15Pin Scart Connector AV1/AV2/AV3PC Input Connector DVI Input ConnectorNormal picture but no sound Check the volume Power buttonCheck the picture contrast and brightness settings Check the volumeWamer amex Programming the Remote Control for Other Components003, 024 019, 023040, 047, 050, 052, 060, 063, 065, 066, 067 NECAfter Sales Service