Samsung 4240 manual Infrared Remote Control

Page 8

BN68-00597A-01 4/2/04 6:38 PM Page 8

Infrared Remote Control

ENG

TURNS THE PDP ON AND OFF

PICTURE EFFECT SELECTION

SOUND EFFECT SELECTION TELETEXT CANCEL

DIRECT CHANNEL SELECTION

PICTURE SIZE/ TELETEXT SIZE SELECTION

VOLUME INCREASE

TEMPORARY SOUND SWITCH-OFF

VOLUME DECREASE

TELETEXT DISPLAY

MENU DISPLAY/

TELETEXT INDEX

MOVE TO THE REQUIRED MENU OPTION/ ADJUST AN OPTION VALUE RESPECTIVELY

PICTURE STILL

TELEWEB DISPLAY (DEPENDING ON THE MODEL)

FASTEXT TOPIC SELECTION

REMOTE CONTROL SETUP

IF YOUR REMOTE CONTROL IS NOT FUNCTIONING PROPERLY, TAKE OUT THE BATTERIES AND PRESS THE RESET BUTTON FOR ABOUT 2~3 SECONDS. RE-INSERT THE BATTERIES AND TRY USING THE REMOTE CONTROL AGAIN.

WHEN YOU PRESS A BUTTON , ‘ ’

APPEARS ALONG WITH SELECTED MODE (TV, VCR, CATV, DVD OR STB) AND REMAINING BATTERIES ON LCD

MAKE THE REMOTE CONTROL WORKS FOR TV, VCR, CATV, DVD PLAYER, STB

AUTOMATIC SWITCH-OFF/

TELETEXT SUB-PAGE

NEXT CHANNEL/

TELETEXT NEXT PAGE/

TELEWEB FORWARD

EXTERNAL INPUT SELECTION/ TELETEXT PAGE HOLD

PREVIOUS CHANNEL/

TELETEXT PREVIOUS PAGE/

TELEWEB BACKWARD

INFORMATION DISPLAY/

TELETEXT REVEAL

TV MODE SELECTION EXIT TELETEXT EXIT TELEWEB (DEPENDING ON THE MODEL)

CONFIRM YOUR CHOICE (STORE OR ENTER)

SOUND MODE SELECTION

TruSurround XT

MODE SELECTION

PIP FUNCTIONS;

-PIP ACTIVATING OR DEACTIVATING (PIP ON)

-SWAPPING THE MAIN AND THE SUB PICTURE (SWAP)

-LOCATION SELECTION (POSITION)

-SOURCE SELECTION (SOURCE)

-SIZE SELECTION (SIZE)

-SCAN

-SELECTING THE CHANNEL OF SUB

PICTURE (P )

VCR/DVD FUNCTIONS;

-REWIND (REW)

-STOP

-PLAY/PAUSE

-FAST FORWARD (FF)

➢The performance of the remote control may be affected by bright light.

8

Image 8

Contents PDP-TELEVISION Warranty Screen Image retentionCell Defect HeightSold Separately Power CordOwner’s Instructions Contents Symbols Actual configuration on your PDP may be different Depending on your modelDepending on your model For further details about connection, refer to pages 55~59Infrared Remote Control Inserting the Batteries in the Remote Control Angle of the PDP can be up to 20 degrees left/rightInstalling the Display on the Wall Attachment Panel Wall Mount Bracket Plastic HangerConnecting External Devices to the PDP Connecting to an Aerial or Cable Television Network Connecting a Satellite Receiver or DecoderRear of the PDP Use the 3M/5M/7M cable supplied by SamsungSwitching On and Off Mains lead is attached to the rear of your PDPBecoming Familiar with the Remote Control Remote control is used mainly toChange channels and adjust the volume Display the on-screen menu systemSetting Up Your Remote Control Plug & Play Feature To start the search, press the Enter buttonIf you want to reset this feature Choosing Your LanguageStoring Channels Automatically SeeBG DK I L Storing ChannelsManuallyAuto PAL Secam or Auto NT3.58 NT4.43 PAL60 Channel mode Skipping Unwanted Channels Skipping unwanted channelsSorting the Stored Channels Assigning Names to Channels Using the LNA Low Noise Amplifier Feature Activating the Child Lock Activating the child lockDynamic Standard Movie Custom High Middle Low Custom Displaying InformationChanging the Picture Standard Adjusting the Picture Settings Custom Options available in PC, DVI Mode ContrastBrightness, Sharpness Colour Tone Cool2, Cool1, Normal, Warm1, Warm2Adjusting the Picture Settings PC or DVI Mode Custom PC mode only Colour1 Colour2 Colour3Setting the Picture PC Mode Preset to the PC mode by using the Source buttonSetting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneColour System and Sound System settings are correct Viewing the Channel Scan Picture Freezing the Current PictureResult Main menu is displayed Result Options available in the Channel group areSelecting the Picture Size Positioning and Sizing the screen using ZoomPC to DVI Mode Selecting the Film Mode DNIeTM Digital Natural Image engineSelect the option Off or On Setting the Blue ScreenSetting the Melody Sound Table of PIP Settings Viewing the Picture In Picture PIPEasy functions of remote control Buttons FeaturePicture Button after changing the subUsing the Digital NR Digital Noise Reduction Feature Changing the Sound Standard Standard Music Movie Speech CustomAdjusting the Sound Settings Adjusting the Volume AutomaticallyStereo Setting the TruSurround XTSelecting the Internal Mute Selecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Switching the Television On and Off Automatically Absent Power OffSatellite STB, AV Receiver, DVD Receiver, Game Viewing an External Signal SourceAV1, AV2, AV3, S-Video1,S-Video2,Component1 Redirecting an Input to the External Output Teletext Feature ContentsDisplaying the Teletext Information Press the TTX/MIX button againSelecting Display Options To display PressSelecting a Teletext TeleWeb Feature Option Using the TeleWeb Menu after Displaying the TeleWeb Bookmarking the currentEntering the bookmarked URL Opening the HomeEasy Accessing the TeleWeb Service via the Remote Control TeleWebConnecting to the External Devices Input/Output SpecificationRear of the TV InputConnecting to the S-Video Input Rear of the TV Side of the TVConnecting to the DVI Input Connecting to the PC InputConnecting to the Component Input Connecting Additional SpeakersTo Display the DVD Home Theater Connecting and Using the Home Theater SystemConnecting the Home Theater System Installing the Speakers This speaker installation guide is for the 4240 ModelHow to Assemble the Speakers Wall Mount Bit colour Shown at left is a typical screen for Display dialog boxVideo Signal Dot x Line Vertical Horizontal NVidia chipsetScart Connector AV1/AV2/AV3 PC Input ConnectorDVI Input Connector 15PinPower button Check the picture contrast and brightness settingsCheck the volume Normal picture but no sound Check the volumeProgramming the Remote Control for Other Components 003, 024019, 023 Wamer amexNEC 040, 047, 050, 052, 060, 063, 065, 066, 067After Sales Service