Samsung PAL60 manual Screen Image retention

Page 2

Important !

ENG

◆Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”.

To avoid such image retention, reduce the degree of brightness and contrast of this screen when displaying a still image.

◆Cell Defect

The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9 percent active cells, there may be some cells that do not produce light or remain lit.

◆Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height and do not install and operate there.

◆Warranty

-Warranty does not cover any damage caused by image retention.

-Burn-in is not covered by the warranty.

2

Image 2

Contents PDP-TELEVISION Screen Image retention Video Cable Checking PartsSold Separately Scart CableContents Symbols ContentsDepending on your model Actual configuration on your PDP may be differentYour New Plasma Display Panel Rear Panel For further details about connection, refer to pages 52~56Infrared Remote Control Inserting the Batteries in the Remote Control Assembling the Stand-BaseInstalling the Display on the Wall Attachment Panel Wall Mount Bracket Plastic HangerConnecting External Devices to the PDP Connecting Speakers Ferrite Cores Using a Coaxial cable Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Rear of the PDPTo switch your PDP off, press the I / button again Switching On and OffPlacing in Standby Mode Mains lead is attached to the rear of your PDPChange channels and adjust the volume Becoming Familiar with the Remote ControlRemote control is used mainly to Display the on-screen menu systemPlug & Play Feature To start the search, press the Enter buttonIf you want to reset this feature Choosing Your LanguageStoring Channels Automatically SeeAuto PAL Secam or Storing ChannelsManuallyYou wish to identify Auto NT3.58 NT4.43 PAL60Channel mode Skipping Unwanted Channels Skipping unwanted channelsSorting the Stored Channels Assigning Names to Channels Activating the Child Lock Activating the child lockDynamic Standard Movie Custom High Middle Low Custom Displaying InformationChanging the Picture Standard Result The Custom menu is displayed Adjusting the Picture SettingsCustom Options available in PC, DVI Mode Contrast Brightness, SharpnessAdjusting the Picture Settings PC or DVI Mode Custom PC mode only Colour1 Colour2 Colour3Setting the Picture PC Mode Displayed againSetting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneColour System and Sound System settings are correct Viewing the Channel Scan Picture Freezing the Current PicturePositioning and Sizing the screen using Zoom Selecting the Picture SizeSelecting the Film Mode DNIeTM Digital Natural Image engineMelody sounds when the television is powered on or off Setting the Blue ScreenSetting the Melody Sound TV Ext.1 Ext.2 AV S-Video Component PC DVI Table of PIP SettingsViewing the Picture In Picture PIP Tvpip Using the Digital NR Digital Noise Reduction Feature Using the LNA Low Noise Amplifier FeatureChanging the Sound Standard Standard Music Movie Speech CustomAdjusting the Sound Settings Adjusting the Volume AutomaticallyStereo Setting the TruSurround XTSelecting the Internal Mute Selecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Switching the Television On and Off Automatically Absent Power OffSatellite STB, AV Receiver, DVD Receiver, Game Viewing an External Signal SourceExt.1 Ext.2 AV S-Video Component PC DVI Redirecting an Input to the External Output Teletext Feature ContentsDisplaying the Teletext Information Press the TTX/MIX button againSelecting Display Options To display PressSelecting a Teletext Rear of the TV Connecting to the External DevicesInput/Output Specification InputConnecting to the S-Video Input Connecting to the DVI Input Connecting to the PC InputConnecting to the Component Input To Display the DVD Home Theater Connecting and Using the Home Theater SystemConnecting the Home Theater System Setting up Your PC Software Windows only Correct settings for these two variables areNVidia chipset Input Mode PC/DVIVideo Signal Dot x Line Vertical Horizontal PC Input Connector 15Pin Pin ConfigurationsScart Connector Ext1,Ext2 DVI Input ConnectorCheck the volume Power buttonCheck the picture contrast and brightness settings Normal picture but no sound Check the volumeMemo After Sales Service