Samsung PAL60 manual Plug & Play Feature, To start the search, press the Enter button

Page 17

Plug & Play Feature

When the television is initially powered ON, several basic customer settings proceed automatically and subsequently. The following settings are available.

1If the television is in Standby mode, press the POWER ( ) button on the remote control.

Result: The message Plug & Play is displayed. It flickers for a little while, and then the Language menu is automatically displayed.

2Select the appropriate language by pressing the or button.

3Press the ENTER ( ) button to confirm your choice.

Result: The message Antenna input check is displayed.

4Make sure that the antenna is connected to the TV, and then press the ENTER ( ) button.

Result: The Country menu is displayed.

5Select your country by pressing the or button.

6Press the ENTER ( ) button to confirm your choice. Result: The Auto Store menu is displayed.

7To start the search, press the ENTER ( ) button.

Result: The search will end automatically. Channels are sorted and stored in an order which reflects their position in the frequency range (with lowest first and highest last). When it has finished, the Clock Set menu is displayed.

To stop the search before it has finished or return to normal viewing, press the MENU ( ) button.

8Press the ENTER ( ) button to set the Clock. Press the œ or button to move to the hour or minute. Set the hour or minute by pressing the or button.

9When it has finished, the message Enjoy Your Watching is displayed, and then the channel which has been stored will be activated.

ENG

Plug & Play

Press ENTER to Start Plug & Play

Start

Enter

Exit

Language

Move Enter

Plug & Play

Antenna Input Check

Country

Country

Austria

Belgium

Croatia

Denmark

Finland

France

Germany

More

Move

Enter

Auto Store

Press ENTER to start channel memory

40MHz 0%

Start

Enter

Stop

Auto Store

Channel store in process.

Storing.

57MHz 1%

Stop

 

Enter

Stop

Clock

 

Hour

Min

01

00

Adjust

Move

Stop

Enjoy Your Watching

17

Image 17
Contents PDP-TELEVISION Screen Image retention Sold Separately Checking PartsVideo Cable Scart CableContents Contents SymbolsDepending on your model Actual configuration on your PDP may be differentYour New Plasma Display Panel For further details about connection, refer to pages 52~56 Rear PanelInfrared Remote Control Assembling the Stand-Base Inserting the Batteries in the Remote ControlWall Mount Bracket Plastic Hanger Installing the Display on the Wall Attachment PanelConnecting External Devices to the PDP Connecting Speakers Ferrite Cores Connecting a Satellite Receiver or Decoder Connecting to an Aerial or Cable Television NetworkUsing a Coaxial cable Rear of the PDPPlacing in Standby Mode Switching On and OffTo switch your PDP off, press the I / button again Mains lead is attached to the rear of your PDPRemote control is used mainly to Becoming Familiar with the Remote ControlChange channels and adjust the volume Display the on-screen menu systemTo start the search, press the Enter button Plug & Play FeatureChoosing Your Language If you want to reset this featureSee Storing Channels AutomaticallyYou wish to identify Storing ChannelsManuallyAuto PAL Secam or Auto NT3.58 NT4.43 PAL60Channel mode Skipping unwanted channels Skipping Unwanted ChannelsSorting the Stored Channels Assigning Names to Channels Activating the child lock Activating the Child LockDynamic Standard Movie Custom High Middle Low Custom Displaying InformationChanging the Picture Standard Custom Options available in PC, DVI Mode Contrast Adjusting the Picture SettingsResult The Custom menu is displayed Brightness, SharpnessCustom PC mode only Colour1 Colour2 Colour3 Adjusting the Picture Settings PC or DVI ModeDisplayed again Setting the Picture PC ModeSetting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneColour System and Sound System settings are correct Freezing the Current Picture Viewing the Channel Scan PictureSelecting the Picture Size Positioning and Sizing the screen using ZoomDNIeTM Digital Natural Image engine Selecting the Film ModeMelody sounds when the television is powered on or off Setting the Blue ScreenSetting the Melody Sound TV Ext.1 Ext.2 AV S-Video Component PC DVI Table of PIP SettingsViewing the Picture In Picture PIP Tvpip Using the LNA Low Noise Amplifier Feature Using the Digital NR Digital Noise Reduction FeatureStandard Music Movie Speech Custom Changing the Sound StandardAdjusting the Volume Automatically Adjusting the Sound SettingsStereo Setting the TruSurround XTSelecting the Internal Mute Selecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Absent Power Off Switching the Television On and Off AutomaticallySatellite STB, AV Receiver, DVD Receiver, Game Viewing an External Signal SourceExt.1 Ext.2 AV S-Video Component PC DVI Redirecting an Input to the External Output Contents Teletext FeaturePress the TTX/MIX button again Displaying the Teletext InformationTo display Press Selecting Display OptionsSelecting a Teletext Input/Output Specification Connecting to the External DevicesRear of the TV InputConnecting to the S-Video Input Connecting to the PC Input Connecting to the DVI InputConnecting to the Component Input To Display the DVD Home Theater Connecting and Using the Home Theater SystemConnecting the Home Theater System Correct settings for these two variables are Setting up Your PC Software Windows onlyNVidia chipset Input Mode PC/DVIVideo Signal Dot x Line Vertical Horizontal Scart Connector Ext1,Ext2 Pin ConfigurationsPC Input Connector 15Pin DVI Input ConnectorCheck the picture contrast and brightness settings Power buttonCheck the volume Normal picture but no sound Check the volumeMemo After Sales Service