Samsung PAL60 manual Selecting the Sound Mode depending on the model

Page 42

Selecting the Sound Mode (depending on the model)

ENG

The “DUAL I-II” button displays/controls the processing and output of the audio signal. When power is switched on, the mode is automatically preset to either “Dual-I ” or “Stereo”, depending on the current transmission.

		Type of broadcast	On-screen indication

		Regular broadcast	Mono (Normal use)
		(Standard audio)	Mono (Normal use)
		(Standard audio)

		Regular +	NICAM Mono ↔ Mono
	NICAM	NICAM Mono	NICAM Mono ↔ Mono
	NICAM	NICAM Mono
	Stereo	NICAM Stereo	NICAM Stereo ↔ Mono
			NICAM Stereo ↔ Mono
			(Forced mono)
			(Forced mono)

		NICAM Dual-I/II	NICAM Dual-I→
		NICAM Dual-I/II	NICAM Dual-II→
			Mono

		Regular broadcast	Mono
		(Standard audio)	Mono
		(Standard audio)
	A2
	A2	Bilingual or Dual-I/II	Dual-I↔ Dual-II
	Stereo	Bilingual or Dual-I/II	Dual-I↔ Dual-II
	Stereo

		Stereo	Stereo ↔ Mono
		Stereo	(Forced mono)
			(Forced mono)

➣◆ If the receiving conditions deteriorate, listening will be easier if the mode is set to the Mono.

◆If the stereo signal is weak and an automatic switching occurs, then switch to the Mono.

◆When receiving a mono sound in the AV mode, connect to the “AUDIO-L” input connector on the side of the television. If the mono sound comes out only from left speaker, press the Dual I-IIbutton.

42

Image 42

Contents PDP-TELEVISION Screen Image retention Video Cable Checking PartsSold Separately Scart CableContents Symbols ContentsActual configuration on your PDP may be different Your New Plasma Display PanelDepending on your model Rear Panel For further details about connection, refer to pages 52~56Infrared Remote Control Inserting the Batteries in the Remote Control Assembling the Stand-BaseInstalling the Display on the Wall Attachment Panel Wall Mount Bracket Plastic HangerConnecting External Devices to the PDP Connecting Speakers Ferrite Cores Using a Coaxial cable Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Rear of the PDPTo switch your PDP off, press the I / button again Switching On and OffPlacing in Standby Mode Mains lead is attached to the rear of your PDPChange channels and adjust the volume Becoming Familiar with the Remote ControlRemote control is used mainly to Display the on-screen menu systemPlug & Play Feature To start the search, press the Enter buttonIf you want to reset this feature Choosing Your LanguageStoring Channels Automatically SeeAuto PAL Secam or Storing ChannelsManuallyYou wish to identify Auto NT3.58 NT4.43 PAL60Channel mode Skipping Unwanted Channels Skipping unwanted channelsSorting the Stored Channels Assigning Names to Channels Activating the Child Lock Activating the child lockDisplaying Information Changing the Picture StandardDynamic Standard Movie Custom High Middle Low Custom Result The Custom menu is displayed Adjusting the Picture SettingsCustom Options available in PC, DVI Mode Contrast Brightness, SharpnessAdjusting the Picture Settings PC or DVI Mode Custom PC mode only Colour1 Colour2 Colour3Setting the Picture PC Mode Displayed againSetting the Picture PC Mode Using the Fine Tune Colour System and Sound System settings are correctIf reception is weak, you can fine tune a channel manually Viewing the Channel Scan Picture Freezing the Current PicturePositioning and Sizing the screen using Zoom Selecting the Picture SizeSelecting the Film Mode DNIeTM Digital Natural Image engineSetting the Blue Screen Setting the Melody SoundMelody sounds when the television is powered on or off Table of PIP Settings Viewing the Picture In Picture PIPTV Ext.1 Ext.2 AV S-Video Component PC DVI Tvpip Using the Digital NR Digital Noise Reduction Feature Using the LNA Low Noise Amplifier FeatureChanging the Sound Standard Standard Music Movie Speech CustomAdjusting the Sound Settings Adjusting the Volume AutomaticallySetting the TruSurround XT Selecting the Internal MuteStereo Selecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Switching the Television On and Off Automatically Absent Power OffViewing an External Signal Source Ext.1 Ext.2 AV S-Video Component PC DVISatellite STB, AV Receiver, DVD Receiver, Game Redirecting an Input to the External Output Teletext Feature ContentsDisplaying the Teletext Information Press the TTX/MIX button againSelecting Display Options To display PressSelecting a Teletext Rear of the TV Connecting to the External DevicesInput/Output Specification InputConnecting to the S-Video Input Connecting to the DVI Input Connecting to the PC InputConnecting to the Component Input Connecting and Using the Home Theater System Connecting the Home Theater SystemTo Display the DVD Home Theater Setting up Your PC Software Windows only Correct settings for these two variables areInput Mode PC/DVI Video Signal Dot x Line Vertical HorizontalNVidia chipset PC Input Connector 15Pin Pin ConfigurationsScart Connector Ext1,Ext2 DVI Input ConnectorCheck the volume Power buttonCheck the picture contrast and brightness settings Normal picture but no sound Check the volumeMemo After Sales Service