Samsung PPM 42S3 manual Inserting the Batteries in the Remote Control, Assembling the Stand-Base

Page 15

BN68-00457B-01_ENG 2003.10.23 3:20 PM Page 15

Inserting the Batteries in the Remote Control

ENG

You must insert or replace the batteries in the remote control when you:

◆Purchase the PDP

◆ Find that the remote control is no longer operating correctly

1Remove the cover on the rear of the remote control by pressing the symbol downwards and then pulling firmly to remove it.

2Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking

care to respect the polarities:

◆ - on the battery against - on the remote control

◆+ on the battery against + on the remote control

3 Replace the cover by aligning it with the base of the remote control and pressing it back into place.

Assembling the Stand-Base

Fit the Stand-Base into the guide hole on the bottom of the monitor and tighten the left and right sides using four screws for each side.

➢◆ Two or more people should carry the PDP. Never lay the PDP on the floor because of

possible damage to the screen. Always store the PDP upright.

◆ For the PPM63H3 model, please see the instruction for the SMM6330 stand.

15

Image 15

Contents PDP-MONITOR Thank You for Choosing Samsung Important Safety Informations UL1492 Important Safety Informations UL1492 Important Safety Instructions UL6500 User Instructions FCC InformationImportant Warranty Information Regarding PDP Format Viewing Cell Defect WarrantyUser Instructions Screen Image retentionImportant Notice Wiring the Mains Power Supply Plug UK OnlyContents Contents Symbols Your New Plasma Display Panel Rear Panel Your New Plasma Display PanelBecoming Familiar with the Remote Control Assembling the Stand-Base Inserting the Batteries in the Remote ControlInstallation Notes Installing the Display on the Wall Attachment PanelExterior of the PDP may be different than the picture Example for 2x2 Video Wall function Installing the Display VerticallyPPM42S3 Connecting SpeakersConnecting Speakers Switching On and Off Choosing Your LanguageMains lead is attached to the rear of your PDP Changing the Picture Mode Selecting the Color System Video or S-Video ModeNormal Warm1 Warm2 Cool2 Cool1 Adjusting the Picture SettingsAdjusting the Picture Settings PC or DVI Mode Selecting the Picture Size Activating/Deactivating the Digital Noise Reduction FeatureFreezing the Current Picture Changing the Sound ModeAdjusting the Sound Settings Pseudo Stereo / Virtual Surround Extra Sound SettingsAuto Volume MelodyAdjusting the Screen Position and Scale Adjusting the Image Preferences PC Mode Locking the Control buttons Setting the MDC Multiple Display ControlYou can prevent the residual image of the PDP Protecting the Screen BurningYou can get the various display effect with many PDPs Setting the Multiple ScreenDisplaying the PC Information Displaying the Setting InformationSetting and Displaying the Current Time Absent Power Off Switching On and Off AutomaticallySetting the Film Mode Turning On the FanYou can use the Fan if you are anxious for the PDP Viewing the Picture In Picture PIP SEL Easy functions of remote controlViewing Pictures From External Sources Listening to the Sound of the Sub PictureSub picture Rear of the PDP Connecting to the Audio/Video InputConnecting to the DVD/DTV Receiver Input Connecting to the S-Video InputConnecting to the Rgbpc Input Connecting to the DVI Input1024 x 768 pixels PPM50/63H3 Setting up Your PC Software Windows onlyDVI Input Connector 24Pin Pin ConfigurationsRgbpc Input Connector 15Pin RS232C Connector 9PinPPM42S3 PPM50H3 PPM63H3 Input Mode PC/DVIPower Saver PC1 mode only Liquids Care and MaintenanceIdentifying Problems TemperatureCOMPONENT2/RGB2PC2 Technical SpecificationsMemo Memo After Sales Service