Samsung PPM 42S3 manual Important Safety Informations UL1492

Page 4

BN68-00457B-01_ENG 2003.10.23 3:20 PM Page 4

Important Safety Informations (UL1492) (continued)

ENG

◆Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. When installing an outside antenna system, be extremely careful to keep from touching the power lines or circuits. Contact with such lines can be fatal.

◆Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.

◆Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts. Never spill liquid of any kind on the PDP.

◆Ground outdoor antennas. If an outside antenna or cable system is connected to the PDP, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984, provides information about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

◆Do not attempt to service the PDP yourself. Refer all servicing to qualified service personnel. Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

-when the power-supply cord or plug is damaged

-if liquid has been spilled on the unit or if objects have fallen into the unit

-if the PDP has been exposed to rain or water

-if the PDP does not operate normally by following the operating instructions

-if the PDP has been dropped or the cabinet has been damaged

-when the PDP exhibits a distinct change in performance

◆If you make adjustments yourself, adjust only those controls that are covered by the operating instructions. Adjusting other controls may result in damage and will often require extensive work by a qualified technician to restore the PDP to normal.

◆When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in additional damage to the unit.

◆Upon completion of any service or repairs to this PDP, ask the service technician to perform safety checks to determine that the PDP is in a safe operating condition.

◆The PDP can properly operate in a temperature range of 32~104°F(0~40°C) and 80% humidity. Do not use in a hot and humid place.

◆Before moving the PDP equipped with speakers, separate the speakers from the PDP. If you move the PDP with the speakers attached, it may result in damage or injury.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents PDP-MONITOR Thank You for Choosing Samsung Important Safety Informations UL1492 Important Safety Informations UL1492 Important Safety Instructions UL6500 FCC Information User InstructionsImportant Warranty Information Regarding PDP Format Viewing Warranty User InstructionsScreen Image retention Cell DefectWiring the Mains Power Supply Plug UK Only Important NoticeContents Symbols ContentsYour New Plasma Display Panel Your New Plasma Display Panel Rear PanelBecoming Familiar with the Remote Control Inserting the Batteries in the Remote Control Assembling the Stand-BaseInstalling the Display on the Wall Attachment Panel Installation NotesExterior of the PDP may be different than the picture Installing the Display Vertically Example for 2x2 Video Wall functionConnecting Speakers PPM42S3Connecting Speakers Choosing Your Language Switching On and OffMains lead is attached to the rear of your PDP Selecting the Color System Video or S-Video Mode Changing the Picture ModeAdjusting the Picture Settings Normal Warm1 Warm2 Cool2 Cool1Adjusting the Picture Settings PC or DVI Mode Activating/Deactivating the Digital Noise Reduction Feature Selecting the Picture SizeChanging the Sound Mode Freezing the Current PictureAdjusting the Sound Settings Extra Sound Settings Auto VolumeMelody Pseudo Stereo / Virtual SurroundAdjusting the Screen Position and Scale Adjusting the Image Preferences PC Mode Setting the MDC Multiple Display Control Locking the Control buttonsProtecting the Screen Burning You can prevent the residual image of the PDPSetting the Multiple Screen You can get the various display effect with many PDPsDisplaying the Setting Information Displaying the PC InformationSetting and Displaying the Current Time Switching On and Off Automatically Absent Power OffTurning On the Fan Setting the Film ModeYou can use the Fan if you are anxious for the PDP Viewing the Picture In Picture PIP Easy functions of remote control SELListening to the Sound of the Sub Picture Viewing Pictures From External SourcesSub picture Connecting to the Audio/Video Input Rear of the PDPConnecting to the S-Video Input Connecting to the DVD/DTV Receiver InputConnecting to the DVI Input Connecting to the Rgbpc InputSetting up Your PC Software Windows only 1024 x 768 pixels PPM50/63H3Pin Configurations Rgbpc Input Connector 15PinRS232C Connector 9Pin DVI Input Connector 24PinInput Mode PC/DVI PPM42S3 PPM50H3 PPM63H3Power Saver PC1 mode only Care and Maintenance Identifying ProblemsTemperature LiquidsTechnical Specifications COMPONENT2/RGB2PC2Memo Memo After Sales Service
Top Page Image Contents