Samsung SPP4251 manual Setting Up Your Remote Control

Page 33

Setting Up Your Remote Control

This PDP's remote control can operate almost any VCR, cable box or DVD. After it has been set up properly, your remote control can operate in four different modes :TV , VCR, Cable, DVD or STB. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose.

Note : The remote control may not be compatible with all DVD Players, VCRs, Cable boxes.

The remote control can only operate STB made by Samsung.

Setting Up the Remote to Operate Your VCR, Cable box or DVD player

1 Turn off your VCR. (or Cable box, DVD player)

Press the MODE button. Mode is changed whenever

2 MODE button is pressed.

3 Press the SET button on your TV's remote control.

Using the number buttons on your remote control,

4 enter three digits of the VCR (or Cable box, DVD player) code listed on page 35 of this manual for your brand of VCR (or CATV, DVD). Make sure you enter three digits of the code, even if the first digit is a "0".

(If more than one code is listed, try the first one.)

Press the POWER button on the remote control.

5 Your VCR (or CATV, DVD) should turn on if your remote is set up correctly. If your VCR (or CATV, DVD) does not turn on after setup, repeat steps

2, 3, and 4, but try one of the other codes listed for your brand of VCR (or CATV, DVD).

If no other codes are listed, try each code, 000 through 089 (or Cable box: 000 through 077, DVD player: 000 through 008).

Notes

When your remote control is in “VCR” mode, the VCR control buttons (STOP, REW, PLAY/PAUSE, FF) still operate your VCR.

When your remote control is in “CATV” or “DVD” mode, the VCR control buttons (STOP, REW, PLAY/PAUSE, FF) still operate your VCR.

You do not need to program the remote for Samsung STBs as the codes are pre-programmed.

34

Image 33
Contents Owner’s Instructions User Instructions WarrantyScreen Image retention Cell DefectTable of Contents General Information Speakers Power IndicatorSource button Menu buttonPC Input RGB in / Audio Video Input Audio Input L, RVIDEO1, S-VIDEO2 AV1, AV2, AV3Remote Control Buttons Remote Control Operation Range ∑ Reset button¸ SRS Tsxt button ˛ MTS buttonWall Mount Bracket Installation NotesFixing the PDP panel to the wall attachment panel bracket Connecting External Devices to the PDP How to Adjust Mounting Angle Factory defaultChanging the angle How to assemble the Stand-Base Connections Antennas with 75-ohm Round Leads Connecting VHF and UHF AntennasCable without a Cable Box Connecting Cable TVPage Videotape Playback Connecting a VCRConnecting a Camcorder Viewing camcorder tapesViewing Tapes Connecting a DVD Player 480i, 480p Playing DVDTo Play DVD To Watch DTV Watching DTVOperation Turning the PDP On and Off Viewing the Menus and DisplaysViewing the Menus Displaying Status Information Press the Enter button to confirm your choice Plug & Play FeatureEnjoy your watching Setup Language English Time Caption Digital NR Chip Memorizing the Channels Selecting the Video Signal-sourceStoring Channels in Memory Automatic Method Adding and Erasing Channels Manual Method To View Memorized Channel PIP Mode Adjusting the Volume Using MuteChanging Channels Setting Up Your Remote Control Remote Control Codes Setting the Signal Source Viewing an External Signal SourceAssigning Names to External input mode Picture Control Customizing the Picture Using Automatic Picture Settings Selecting the Color Tone DNIe Digital Natural Image engine Changing the Screen Size Panorama 169WideZoom 3NormalStill Freezing the PictureSelecting the PIP Screen Viewing the Picture-in-PictureSelecting an External Signal Swapping the Contents of the PIP Image and Main Image Changing the Size of the PIP Window Changing the Location of the PIP Image Selecting a Signal Source Antenna or Cable for PIP Changing the PIP Channel Sound Control Customizing the Sound Using Automatic Sound Settings Choosing a Multi-Channel Sound MTS Soundtrack Using the Auto Volume TruSurround XT, SRS and Symbol Setting the TruSurround XTListening to the Sound of the SubPIP Picture PC or DVI Mode Selecting the Internal Mute Channel Control Fine Tuning Channels LNA Low Noise Amplifier Connecting a PC and Operation To watch the PC screen Connecting a PCPin Configuration Setting up Your PDP Plug and PlaySub Cable How to Set up Your PC Software Windows only IBM PC / AT Adjusting the R.G.B Adjusting the PC ScreenChanging the Position of the Image Picture Automatic Adjustment Picture Quality AdjustmentCoarse Adjustment Fine Tuning Fine Information Time Setting Setting the Clock Setting the Sleep Timer Setting the Timers Off Function Description Selecting a Menu Language Digital Noise Reduction Selecting the Film Mode Setting the Melody Sound Setting the Blue Screen Viewing Closed Captions Setting Up Your Personal ID Number PIN Using the V-ChipHow to Enable/Disable the V-Chip How to Set up Restrictions using the TV guidelines Move Enter Return Mpaa Rating Page Appendix Problem TroubleshootingIdentifying Problems Care and MaintenanceTemperature LiquidsVideo input SpecificationsMemo 104 105 BN68-00618A-01