Samsung SPP4251 manual Ibm Pc / At

Page 67

Notes:

Both screen position and size will vary, depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported:

Video Signal	Resolution	Vertical	Horizontal	Vertical	Horizontal
	(Dot X Line)	Frequency(Hz)	Frequency(KHz)	Polarity	Polarity

	640 X 350	70.086	31.469	N	P
	640 X 350	85.080	37.861	N	P
		85.080	37.861	N	P
	640 X 400	85.080	37.861	P	N
	720 X 400	70.087	31.469	P	N
	720 X 400	85.039	37.927	P	N
		85.039	37.927	P	N
		59.940	31.469	N	N
	640 X 480	72.809	37.861	N	N
	640 X 480	75.000	37.500	N	N
		75.000	37.500	N	N
IBM PC / AT		85.061	43.269	N	N
Compatible		56.250	35.156	N/P	N/P
Compatible		60.317	37.897	P	P
		60.317	37.897	P	P
	800 X 600	72.188	48.077	P	P
		75.000	46.875	P	P
		85.061	53.674	P	P
		60.000	29.838
	848 X 480	72.000	36.072	nVidia chipset
		75.000	37.650
		60.004	48.363	N	N
	1024 X 768	70.069	56.476	N	N
	1024 X 768	75.029	60.023	P	P
		75.029	60.023	P	P
		84.997	63.677	P	P

•The interlace mode is not supported.

•The PDP operates abnormally if a non-standard video format is selected.

•This sheet conforms to IBM/VESA regulations and is prepared on the basis of Analog Input.

•The DVI Mode is supported same as above table.

Notes:

•When this PDP is used as a PC display, 32-bit color is supported.

•Depending on the manufacturer, your PC display screen might appear different. (and depending on your particular version of Windows.)

Check your PC instruction book for information about connecting your PC to a PDP.

•If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5kHZ (horizontal).

•In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the TV/VIDEO button on the remote control or SOURCE button on the front panel to enter the VIDEO mode. Also, make sure that the PC is connected.

•Connect only a PC monitor to the monitor output port while viewing the PC screen. (Otherwise, random signals might appear).

71

Image 67

Contents Owner’s Instructions Cell Defect WarrantyUser Instructions Screen Image retentionTable of Contents General Information Menu button Power IndicatorSpeakers Source buttonAV1, AV2, AV3 Video Input Audio Input L, RPC Input RGB in / Audio VIDEO1, S-VIDEO2Remote Control Buttons ˛ MTS button ∑ Reset buttonRemote Control Operation Range ¸ SRS Tsxt buttonWall Mount Bracket Installation NotesFixing the PDP panel to the wall attachment panel bracket Connecting External Devices to the PDP Factory default How to Adjust Mounting AngleChanging the angle How to assemble the Stand-Base Connections Antennas with 75-ohm Round Leads Connecting VHF and UHF AntennasCable without a Cable Box Connecting Cable TVPage Videotape Playback Connecting a VCRViewing camcorder tapes Connecting a CamcorderViewing Tapes Playing DVD Connecting a DVD Player 480i, 480pTo Play DVD To Watch DTV Watching DTVOperation Viewing the Menus and Displays Turning the PDP On and OffViewing the Menus Displaying Status Information Press the Enter button to confirm your choice Plug & Play FeatureEnjoy your watching Setup Language English Time Caption Digital NR Chip Memorizing the Channels Selecting the Video Signal-sourceStoring Channels in Memory Automatic Method Adding and Erasing Channels Manual Method To View Memorized Channel PIP Mode Using Mute Adjusting the VolumeChanging Channels Setting Up Your Remote Control Remote Control Codes Setting the Signal Source Viewing an External Signal SourceAssigning Names to External input mode Picture Control Customizing the Picture Using Automatic Picture Settings Selecting the Color Tone DNIe Digital Natural Image engine Changing the Screen Size 3Normal 169WidePanorama ZoomStill Freezing the PictureSelecting the PIP Screen Viewing the Picture-in-PictureSelecting an External Signal Swapping the Contents of the PIP Image and Main Image Changing the Size of the PIP Window Changing the Location of the PIP Image Selecting a Signal Source Antenna or Cable for PIP Changing the PIP Channel Sound Control Customizing the Sound Using Automatic Sound Settings Choosing a Multi-Channel Sound MTS Soundtrack Using the Auto Volume TruSurround XT, SRS and Symbol Setting the TruSurround XTListening to the Sound of the SubPIP Picture PC or DVI Mode Selecting the Internal Mute Channel Control Fine Tuning Channels LNA Low Noise Amplifier Connecting a PC and Operation To watch the PC screen Connecting a PCSetting up Your PDP Plug and Play Pin ConfigurationSub Cable How to Set up Your PC Software Windows only IBM PC / AT Adjusting the R.G.B Adjusting the PC ScreenChanging the Position of the Image Picture Automatic Adjustment Picture Quality AdjustmentCoarse Adjustment Fine Tuning Fine Information Time Setting Setting the Clock Setting the Sleep Timer Setting the Timers Off Function Description Selecting a Menu Language Digital Noise Reduction Selecting the Film Mode Setting the Melody Sound Setting the Blue Screen Viewing Closed Captions Setting Up Your Personal ID Number PIN Using the V-ChipHow to Enable/Disable the V-Chip How to Set up Restrictions using the TV guidelines Move Enter Return Mpaa Rating Page Appendix Problem TroubleshootingLiquids Care and MaintenanceIdentifying Problems TemperatureVideo input SpecificationsMemo 104 105 BN68-00618A-01