Samsung PS-42S5S manual Setting up Your PC Software Windows only

Page 64

Setting up Your PC Software (Windows only)

The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)

2

3

4

5

1Right click the mouse on the Windows Desktop, then click on Properties.

The Display Properties will be displayed.

2Click on Settings tab, then set the Display Mode with reference to the Display Modes Table.

You do not need to change the Colours settings.

3Click on Advanced. A new settings dialog box will be displayed.

4Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of setting the Screen refresh rate.

5Click on OK to close the window, then Click on OK button to the Display Properties window. Automatic re-booting may commence at this moment.

6Shutdown the PC, and connect it to your TV. (“Connecting to the PC Input” on page 61)

➢◆ The actual screens on your PC may look different, depending on your particular version of Windows and the type of your PC.

◆When you use your TV as a PC monitor, it supports Colours up to 32 bits.

◆In this case, the display on the TV may look different depending on your particular version of Windows or the PC manufacturer.

◆When connecting a PC (including the HDMI connection), you must set it to the display settings that are supported by the TV. Otherwise, the message Out of input range will be displayed.

English - 64

Image 64

Contents PDP-TELEVISION User Instructions Power Cord Owner’s InstructionsVideo Cable PC CableContents Symbols Control Panel Front of the TVRear Panel For further details about connection, refer to pages 58~63Infrared Remote Control Inserting the Batteries in the Remote Control Assembling the Stand-BaseInstalling the Display on the Wall Attachment Panel Wall Bracket Hinge Accessories Plastic Hanger ScrewAdjust the length Insert and tighten the Captive ScrewStay in place after installation Insert the screw into the plastic hangerSee the figure below Left and right plastic hangersConnecting to an Aerial or Cable Television Network Connecting a Satellite Receiver or DecoderUsing a coaxial cable Rear of the TVTo switch your television off, press the power button again Switching Your Television On and OffMains lead is attached to the rear of your television Change channels and adjust the volume Familiarizing Yourself with the Remote ControlTheir functions Plug & Play Feature Press the Enter button to set the clockFor further details on settings, refer to the previous Choosing Your LanguagePress the Menu button Result The main menu is displayed Press the Enter buttonStoring Channels Automatically Select your Country by pressing the … or † buttonStoring ChannelsManually AutoChannel mode Skipping Unwanted Channels Sorting the Stored Channels This operation allows you to change the programme numbersAssigning Names to Channels Locking the Channel Using the LNA Low Noise Amplifier Feature Fine Tuning Channel Reception Displaying Information Changing the Picture StandardResult Following options are available Customizing the Picture SettingsTint Ntsc only Setting the Picture PC Mode Preset to the PC mode by pressing the Source buttonSetting the Picture PC Mode Positioning and Sizing the screen using Zoom Selecting the Picture SizeViewing the DNIe Demonstration Freezing the Current PictureSetting the My Colour Control Easy Control Emphasizing clear bluesEmphasizing mild greens Emphasizing warm skin coloursSetting the My Colour Control Detail Control Setting the Blue Screen Using the Colour Weakness Enhancement Feature Using the Energy Saving Feature Viewing the Picture in Picture PIP TV Ext.1 Ext.2 AV S-VideoTvpip PIP Buttons Feature Easy functions of the remote controlTable of PIP Settings Using the Digital NR Noise Reduction Feature Preventing Screen Burn-in Horizontal Dot Vertical Line TimeReducing the Effects of Screen Burn Changing the Sound Standard Standard Music Movie Speech CustomCustomizing the Sound Settings Adjusting the Volume AutomaticallySetting the TruSurround XT Off 3D Mono StereoSetting the Melody Sound Selecting the Internal MuteSelecting the Sound Mode depending on the model Setting and Displaying the Current Time Setting the Sleep Timer Switching the Television On and Off Automatically Auto Power Off Viewing an External Signal Source Hdmi on the TV’s rear panelRedirecting an Input to the External Output Teletext Feature Part ContentsDisplaying the Teletext Information Press the TTX/MIX button againSelecting Display Options To display PressSelecting a Teletext Input/Output Specification Connecting to External Input/OutputInput Connecting to the AV Output Connecting to the RCA Input Connecting to the S-Video InputConnecting to the Component Input Connecting to the PC InputConnecting to the HDMI/DVI Compatible Connecting to the Hdmi InputHDMI/DVI in connector is used for equipment with a DVI out Connecting the Home Theater System Connecting Home Theater SystemTo Display the DVD Home Theater Setting up Your PC Software Windows only Input Mode PC Video Signal Resolution Vertical HorizontalYour TV comes equipped with a universal remote control. Remote control might not be compatible with allSamsung VCRs, DVD players, Cable boxes, and Set-Top BoxsProgramming the Remote Control for Other Components Power button Check the picture contrast and brightness settingsCheck the volume Normal picture but no sound Check the volumeMemo Memo Memo After Sales Service Correct Disposal of This Product