Samsung PS-50P4H1 manual Connecting External Devices to the PDP

Page 11

Installing the Display on the Wall Attachment Panel (continued)

➢The exterior of the PDP may be different than the picture. (Assembly and installation of the plastic hanger is the same.)

1	Remove the screws from the back of the PDP. 2	Use the screws and assemble the plastic
		hanger.

3Tighten the screws of the plastic hanger to the back side of the PDP.

☛◆ Please ask the installers to install the wall mount bracket.

◆Please be sure to check if the plastic hanger is completely secured on both the left and right side after hanging the PDP on the wall mount bracket.

◆Please avoid catching your fingers while installing and adjusting the angle.

◆Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP.

4Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be separated from wall mount bracket.

PDP panel

Wall attachment panel bracket Wall

ConnectingExternalDevicestothePDP

◆To connect external devices such as a DVD or a Home Theater System to the PDP, please refer to following instructions:

1 Be sure to remove the safety pins underneath the PDP.

◆If the safety pins are not removed, the angle cannot be adjusted. Any attempt to do so may cause damage to the PDP.

2Pull out the bottom of the PDP (which has been attached to the Wall Mount Bracket) in the direction indicated by the arrows (refer to the illustration) until it clicks.

◆ Using the PDP After Connecting External Devices.

Be sure to secure the PDP by inserting the 2 safety pins after readjusting the angle of the PDP to 0o.

◆For safety, be sure to secure the PDP using the safety pins.

If the safety pins are not used, the PDP may fall, causing serious injury.

English - 11

Image 11

Contents PDP-TELEVISION User Instructions Checking Parts Contents Contents SymbolsFront Panel Your New Plasma Display PanelSide of the TV Infrared Remote Control Assembling the Stand-Base Inserting the Batteries in the Remote ControlInstallation Notes Installing the Display on the Wall Attachment PanelConnecting External Devices to the PDP Rear of the PDP Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Using a Coaxial cablePlacing in Standby Mode Switching On and OffDisplay the on-screen menu system Becoming Familiar with the Remote ControlRemote control is used mainly to Change channels and adjust the volumeVCR Setting Up Your Remote ControlTo start the search, press the Enter button Plug & Play FeatureChoosing Your Language If you want to reset this featureStoring Channels Automatically BG DK I L Storing ChannelsManuallyAuto PAL Secam or Channel mode Skipping unwanted channels Skipping Unwanted ChannelsSorting the Stored Channels Assigning Names to Channels Using the LNA Low Noise Amplifier Feature Activating the child lock Activating the Child LockDynamic Standard Movie Custom High Middle Low Custom Displaying InformationChanging the Picture Standard Colour Tone Cool2, Cool1, Normal, Warm1, or Warm2 Adjusting the Picture SettingsBrightness, or Sharpness Custom PC mode only Colour1 Colour2 Colour3 Adjusting the Picture Settings PC or DVI ModeSetting the Picture PC Mode Setting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneColour System and Sound System settings are correct Freezing the Current Picture Viewing the Channel Scan PictureSelecting the Picture Size Positioning and Sizing the screen using ZoomPC to DVI Mode White enhancement Selecting the Film ModeDNIeTM Digital Natural Image engine Setting the My Colour Control Easy Control Setting the My Colour Control Detail Control Setting the Melody Sound Setting the Blue ScreenUsing the Colour Weakness Enhancement Feature Video2 Component1 Component2 PC DVI Viewing the Picture In Picture PIPComponent1, Component2, PC, or DVI Easy functions of remote controlOperates or stops the TV’s internal Fan Using the Digital NR Noise Reduction FeatureSelecting the Fan Pixel Shift selected Protecting the Screen BurningYou can prevent the residual image of the PDP Standard Music Movie Speech Custom Changing the Sound StandardAdjusting the Volume Automatically Adjusting the Sound SettingsSelecting the Internal Mute Setting the TruSurround XTDUAL- I ↔ Dual Selecting the Sound Mode depending on the modelSetting the Sleep Timer Setting and Displaying the Current Time Auto Power Off Switching the Television On and Off AutomaticallySatellite STB, AV Receiver, DVD Receiver, Game Viewing an External Signal SourceAV1, AV2, AV3, S-Video1,S-Video2,Component1 … or † button Press the Enter button to confirm the change Redirecting an Input to the External OutputDisplaying the Teletext Information Teletext FeatureTo display Press Selecting Display OptionsSelecting a Teletext Rear of the TV Connecting to the External DevicesInput/Output Specification Rear of the TV Side of the TV Connecting to the S-Video InputConnecting to the PC Input Connecting to the DVI InputRear of the TV Connecting to the Component InputConnecting the Home Theater System Connecting and Using the Home Theater SystemParts How to Install SpeakersHow to Assemble the SpeakersWall Mount Setting up Your PC Software Windows only FrequencyHz Input Mode PC/DVIPin Configurations Troubleshooting Before Contacting Service Personnel JVC Programming the Remote Control for Other ComponentsNEC Programming the Remote Control for Other ComponentsAfter Sales Service