Samsung PS-42D4S manual Connecting External Devices to the PDP

Page 11

Installing the Display on the Wall Attachment Panel (continued)

➢The exterior of the PDP may be different than the picture.

	(Assembly and installation of the plastic hanger is the same.)		ENG
1	Remove the screws from the back of the PDP. 2	Use the screws and assemble the plastic
		hanger.

3Tighten the screws of the plastic hanger to the back side of the PDP.

☛◆ Please ask the installers to install the wall mount bracket.

◆Please be sure to check if the plastic hanger is completely secured on both the left and right side after hanging the PDP on the wall mount bracket.

◆Please avoid catching your fingers while installing and adjusting the angle.

◆Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP.

4Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be separated from wall mount bracket.

PDP panel

Wall

Wall attachment panel bracket

ConnectingExternalDevicestothePDP

◆To connect external devices such as a DVD or a Home Theater System to the PDP, please refer to following instructions:

1 Be sure to remove the safety pins underneath the PDP.

◆If the safety pins are not removed, the angle cannot be adjusted. Any attempt to do so may cause damage to the PDP.

2Pull out the bottom of the PDP (which has been attached to the Wall Mount Bracket) in the direction indicated by the arrows (refer to the illustration) until it clicks.

◆ Using the PDP After Connecting External Devices.

Be sure to secure the PDP by inserting the 2 safety pins after readjusting the angle of the PDP to 0o.

◆For safety, be sure to secure the PDP using the safety pins.

If the safety pins are not used, the PDP may fall, causing serious injury.

11

Image 11

Contents PDP-TELEVISION Screen Image retention Sold Separately Checking PartsContents Contents SymbolsDepending on your model Actual configuration on your PDP may be differentYour New Plasma Display Panel For further details about connection, refer to pages 52~56 Depending on your modelInfrared Remote Control Assembling the Stand-Base Inserting the Batteries in the Remote ControlWall Mount Bracket Plastic Hanger Installing the Display on the Wall Attachment PanelConnecting External Devices to the PDP Connecting Speakers Ferrite Cores Rear of the PDP Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Mains lead is attached to the rear of your PDP Switching On and OffTo switch your PDP off, press the I / button again Display the on-screen menu system Becoming Familiar with the Remote ControlRemote control is used mainly to Change channels and adjust the volumeTo start the search, press the Enter button Plug & Play FeatureChoosing Your Language If you want to reset this featureStoring Channels Automatically BG DK I L Storing ChannelsManuallyPress the Menu button Result The main menu is displayed Auto PAL Secam or Auto NT3.58 NT4.43 PAL60Channel mode Skipping unwanted channels Skipping Unwanted ChannelsSorting the Stored Channels Assigning Names to Channels Activating the child lock Activating the Child LockDynamic Standard Movie Custom High Middle Low Custom Displaying InformationChanging the Picture Standard Brightness, Sharpness Adjusting the Picture SettingsCustom Options available in PC, DVI Mode Contrast Result The Custom menu is displayedCustom PC mode only Colour1 Colour2 Colour3 Adjusting the Picture Settings PC or DVI ModeButton Adjust for best pictureButton.or Source DisplayedSetting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneColour System and Sound System settings are correct Freezing the Current Picture Viewing the Channel Scan PictureSelecting the Picture Size Positioning and Sizing the screen using ZoomPC to DVI Mode DNIeTM Digital Natural Image engine Selecting the Film ModeMelody sounds when the television is powered on or off Setting the Blue ScreenSetting the Melody Sound TV Ext.1 Ext.2 AV S-Video Component PC DVI Table of PIP SettingsViewing the Picture In Picture PIP Tvpip Result The options available are listed Using the Digital NR Digital Noise Reduction FeatureUsing the LNA Low Noise Amplifier Feature Standard Music Movie Speech Custom Changing the Sound StandardAdjusting the Volume Automatically Adjusting the Sound SettingsStereo Setting the TruSurround XTSelecting the Internal Mute Selecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Absent Power Off Switching the Television On and Off AutomaticallySatellite STB, AV Receiver, DVD Receiver, Game Viewing an External Signal SourceExt.1 Ext.2 AV S-Video Component PC DVI Redirecting an Input to the External Output Contents Teletext FeaturePress the TTX/MIX button again Displaying the Teletext InformationTo display Press Selecting Display OptionsSelecting a Teletext Input Connecting to the External DevicesInput/Output Specification Rear of the TVConnecting to the S-Video Input Connecting to the PC Input Connecting to the DVI InputConnecting to the Component Input To Display the DVD Home Theater Connecting and Using the Home Theater SystemConnecting the Home Theater System Correct settings for these two variables are Setting up Your PC Software Windows onlyNVidia chipset Input Mode PC/DVIVideo Signal Dot x Line Vertical Horizontal DVI Input Connector Pin ConfigurationsScart Connector Ext.1,Ext.2 PC Input Connector 15PinNormal picture but no sound Check the volume Power buttonCheck the picture contrast and brightness settings Check the volumeMemo After Sales Service