Toshiba 56HM195 owner manual TV Guide On Screenª Reminder, After testing and you

Page 40

Chapter 5: TV Guide On Screen™ setup

Setting up the TV Guide On Screenª system (continued)

Screen 20: If your VCR stopped playing the tape after testing, select Yes and press ENTER. Screen 21 appears.

If your VCR did not stop playing the tape

after testing and you

Did your VCR stop playing?

want to test the same code again, select “Test this code again” and press ENTER.

If you want to test a different code, select No and press ENTER. Screen 19 appears.

Note: Many VCRs require testing more than one code.

Screen 21: Review the setup information displayed on your TV screen (an example is shown below).

If the information on your TV screen is correct for your setup, select “Yes, end setup” and press ENTER. Screen 22 appears.

If the information is incorrect, select “No, repeat setup process” and press ENTER. Screen 1 appears.

Screen 22: Congratulations! You have successfully completed TV Guide On Screensystem setup.

Press ENTER to display screen 23.

Screen 23: This screen provides helpful information on using your TV Guide On Screensystem.

Press ENTER to exit the TV Guide On Screensetup and watch TV.

TV Guide On Screenª Reminder

The TV Guide On Screensystem receives program listings data through your Cable or over-the-air video signal. In order to receive regular program listing updates, remember to do the following:

1.Leave the TV in standby mode when it is not in use by turning it OFF but leaving the power cord plugged in.

2.If you have a Cable box connected, leave it ON.

3.If you have a VCR connected, turn it OFF when not in use. (Do not unplug the power cord.) See page 13 for VCR connection instructions.

4.If you have more than one Cable system in your area, you may be prompted to select which Cable system’s program data to download. If so prompted, follow the on-screen instructions.

Note: If the TV power cord is unplugged for an extended period of time, it may take up to 24 hours with the TV in standby mode (power cord plugged in and power OFF) to download the TV Guide On Screenª program schedule. It may take up to a week before an entire program schedule is available.

Turning off the TV Guide On Screenª

automatic display feature

After you set up the TV Guide On Screensystem, the program guide will display automatically (by default) when you turn on the TV. To turn off the automatic program guide:

1.Press TV GUIDE on the remote control to open the TV Guide On Screensystem (if it is not already open).

2.Use the x • buttons to select the Setup menu.

3.Use the yz buttons to select “Change Default Options,” and then press ENTER.

4.Use the yz buttons to select “General Defaults,” and then press ENTER.

5.Set the “Auto Guide” option to Off.

6.Use the yz buttons to select Done, and then press

ENTER.

40

Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.

 

Image 40
Contents 56HM195 62HM195 72HM195 Consumers and their families about television safety Safety PrecautionsStand Model Installation, Care, and Service Important Safety InstructionsFor replacement of the obsolete outlet Frequent or continuous, unplug the power cord Contact a Toshiba Authorized Service CenterLamp in this product has a limited service life. Never attempt to service the TV yourselfContents Viewing the CableCARD menu 110Introduction Features of your new TVWelcome to Toshiba Install the batteries in the remote control See LED indications onConnecting your TV Power Press to turn the TV on and offTV front and side panel controls and connections See LED indications on page 99 for additional informationTV back panel connections 7 !¡Overview of cable types To a Personal Computer PCYou will need For more information, call your local cable operatorTo view encrypted digital channels Connecting a VCR and antenna or Cable TV no Cable box Connecting a camcorderConnecting a VCR and Cable box On Screen recording featuresTwo sets of standard A/V cables To view basic and premium Cable channelsConnecting a VCR and satellite receiver Select the ColorStream HD-1 video input source on the TVTo view premium Cable channels To view the DVD playerYour TV has ColorStream component video inputs To view antenna or Cable channelsSelect the ANT 1 video input source on the TV To record a TV program while watching a DVDConnecting two VCRs To view the antenna or Cable signalSelect the ANT-1 video input source on the TV To view VCRConnecting an HDMIª or a DVI device to the Hdmi input One Hdmi cable type a connector per Hdmi deviceTo connect an Hdmi device, you will need To connect a DVI device, you will needConnecting a digital audio system Connecting an analog audio systemTV’s Digital Audio OUT terminal outputs a Dolby To control the audioTheaterNetª on-screen device control To connect the IR blaster cableTo control the devices IR blaster cable wand approx inch from deviceConnecting IEEE1394 video devices Using analog-compatible IEEE1394 devicesSupported signals Using TheaterNetª on-screen device controlWhen you connect a D-VHS or Avhd device to the TV IEEE1394 device initializationTo edit the IEEE1394 device information IEEE1394 device managementHighlight the device you want to edit and press Enter LINKª connection To connect to the G-LINK ª terminalSee Chapter LINKª IR blaster cable wand approx inch from deviceUsing the remote control Learning about the remote controlRemote control effective range To install the remote control batteries Installing the remote control batteriesDevice mode control after programming Remote Control functional key chart PowerAudio VCR Mute Device code setup Searching and sampling the code of a deviceUsing the volume lock feature Operational feature resetRepeatedly press Mode to select CABLE/SAT mode To reset the volume controls to the original device modeMulti-brand remote control device codes VCRs/PVRsCable boxes Brand CodeCD players ReceiversLaser disks DVD playersMenu layout and navigation Main menu layoutSetup / Installation menu layout Signal Meter Signal Meter WindowNavigating the menu system ANT1TV Guide On Screen setup Setting up the TV Guide On Screenª systemConfiguring the location of your TV To set up the TV Guide On Screenª systemFor additional details, see Setting up the TV Guide On Screenª system After testing and you TV Guide On Screenª ReminderSetting up your TV Configuring the antenna input sourcesTo configure the ANT 1 and ANT 2 input sources Selecting the menu languageProgramming channels automatically Programming channels into the TVÕs channel memoryTo program channels automatically Manually adding and deleting channels in the channel memory Programming your favorite channels Setting up and using TheaterNetª on-screen device control Setting up TheaterNetTo set up TheaterNet device control To remove a device from TheaterNetUsing the TheaterNet control icons To select the deviceÕs control icons directlyTo close the on-screen control icons To view another sourceTheaterNetª IR device codes AmplifiersLaser disk players Miscellaneous audio devicesVideo accessory Hdtv decoder Receivers VCRsTMK BrandSetting the time and date Setting the HDMIª audio modeTo set the Hdmi audio mode To set the Avhd device skip timeSetting the Quick Restartª Feature To set the Quick Restartª featureViewing the CableCARDª menu To view the CableCARDª menuRestore Factory Defaults Viewing the digital signal meterViewing the system status To open the TV Guide On Screenª system BelowRating, stereo, HDTV, new episode Lineup so your favorite stations are listed firstTV Guide On Screenª remote control functions Navigating the TV Guide On Screenª systemPanel Menus Video WindowTo lock/unlock the Video Window TV Guide On Screenª Icons Info BoxInfo Action Bar Small Info Box Large Info Box Listings screen TV Guide On Screenª ServicesEpisode Options panel menu Search screen Example Category searchList of all matching shows for that keyword is displayed Example Keyword searchTo edit or delete a keyword Recordings screen To choose the way recordings are displayedTo view a recording, you can do one of the following Screen a Screen BSet a show to Record from a panel menu Record featuresSchedule screen Manually set a show to Record Recording notification bannerRecord conflict Record iconsSet a show Reminder from a panel menu Remind featuresManually set a show Reminder Remind conflict Reminder notification bannerRemind icons Change system settings Setup screenChange channel display Change default options General defaultsRecord defaults Remind defaultsSelecting the video input source to view Using the TV’s featuresTo select the video input source to view Labeling the video input sources DTV Satellite/DSS Cable Game ConsoleTo label the video input sources To clear the input labelsTuning channels Using the Channel BrowserªTo toggle between Browse mode and Select mode To tune to a channel in Browse modeSetting a channel as the ÒHomeÓ channel for an input To set a channel as Home using the remote controlTo set a channel as Home using the menus Adding and clearing channels in the channel historyTuning your favorite channels Tuning to the next programmed channelSwitching between two channels using Channel Return Switching between two channels using SurfLockªSelecting the picture size Natural picture sizeYou can view many program formats in a variety of picture To select the picture sizeScrolling the TheaterWide picture on None of the picture is hiddenTheaterWide 1 picture size For 43 format program TheaterWide 2 picture size for letter box programsUsing the auto aspect ratio feature To set the scroll settingsTo turn on the auto aspect ratio feature To turn off the auto aspect ratio featureSelecting the lamp mode To set the Cinema Mode to FilmTo set the Cinema Mode to Video To select the lamp modeUsing the POP features Using the POP double-window featureTo display a program in the POP window To close the POP window and tune to the highlighted windowSwitching the speaker audio main or POP POP double-window aspect ratioUsing the Freeze feature Using the favorite channel scan featureTo scan and tune your favorite channels Highlight the window for the channel you want to viewSelecting the picture mode Adjusting the pictureAdjusting the picture quality Using CableClear¨ /DNR digital noise reduction Selecting the color temperatureCableClear/DNR field, select your desired setting To select the color temperatureUsing Mpeg noise reduction Using dynamic contrastTo select the Mpeg noise reduction level To select dynamic contrast preferencesUsing the closed caption mode Advanced closed captionsTo view captions or text To view text Highlight T1, T2, T3, or T4Digital closed captions To select digital closed captionsAdjusting the audio Using the digital audio selectorMuting the sound Selecting stereo/SAP broadcastsUsing the sub-bass system SBS Adjusting the audio qualityUsing the StableSound¨ feature Turning off the built-in speakers Using the SRS WOWª surround sound featureSelecting the optical audio output format Using the media player Media SpecificationsMemory card specifications Jpeg file specificationsUsing the Jpeg picture viewer Media player specificationsUsing the Jpeg picture viewer During the slide showTo set the slide show interval To close the picture viewerUsing the MP3 audio player Memory card care and handlingTo use the mute function To close the MP3 audio playerSetting the On/Off Timer Setting the sleep timerUnderstanding the auto power off feature Understanding the last mode memory featureUsing the Gray Level feature Displaying TV setting information on-screen using RecallUsing the Locks menu Entering the PIN codeIf you cannot remember your PIN code Changing your PIN codeBlocking TV programs and movies by rating V-Chip To block and unblock TV programs and moviesPress z to highlight Edit Rating Limits and press Enter Edit Rating Limits screen below appearsUnlocking programs temporarily Blocking channelsLocking video inputs Using the GameTimerª Using the control panel lock featureTroubleshooting Symptom Solution SAP mode may be on. Set the MTS feature to Stereo modeClosed caption problems Rating Blocking V-Chip problemsLED indications TV Guide On Screenª FAQs Setup101 102 Lamp unit replacement and care When to replace the lamp unitAppendix Replacing the lamp unitHow to replace the lamp unit Grasp the lamp unit handle and gently pull the lamp unitU.S., call Tacp consumer solutions at 1-800-631 Disposing of the used lamp unitSpecifications Edid = Enhanced-Extended Display IdentificationLimited United States Warranty Limited One 1 Year Warranty on Parts and LaborLimited One 1 Year Warranty on Lamp Unit How to Obtain Warranty ServiceLimited Canada Warranty How to Obtain Warranty Services109 Channel programming Index87-90 Picture adjustments Remote controlPicture-out-picture POP 106Toshiba America Consumer PRODUCTS, L.L.C