Toshiba 62HM195, 72HM195 owner manual Using Mpeg noise reduction, Using dynamic contrast

Page 81

Chapter 8: Using the TV’s features

Adjusting the picture (continued)

Using MPEG noise reduction

The MPEG noise reduction feature allows you to reduce visible interference caused by MPEG compression. Choices for MPEG noise reduction are High, Medium, Low and Off. Off is automatically selected when this feature is disabled (“grayed out”).

To select the MPEG noise reduction level:

1.Press MENU and open the Video menu.

2.Highlight Advanced Picture Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

3.In the MPEG Noise Reduction field, select either High, Medium, Low, or Off.

Advanced Picture Settings					ANT 1
	Dynamic Contrast			On
	MPEG Noise Reduction			Low
	CableClear			Auto
	Color Temperature			Cool
	Lamp Mode			Low Power

		Reset		Done

4.To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Using dynamic contrast

When dynamic contrast is set to “On,” the TV will detect changes in the picture quality that affect the appearance of your contrast settings and then automatically adjust the video.

When dynamic contrast is set to “Off,” the settings selected in the Contrast field in Picture Settings will be used.

To select dynamic contrast preferences:

1.Press MENU and open the Video menu.

2.Highlight Advanced Picture Settings and press ENTER.

Video

Picture Settings

Advanced Picture Settings

Theater Settings

3. In the Dynamic Contrast field, select either On or Off.

Advanced Picture Settings					ANT 1
	Dynamic Contrast			On
	MPEG Noise Reduction			Low
	CableClear			Auto
	Color Temperature			Cool
	Lamp Mode			Low Power

		Reset		Done

4.To save the new settings, highlight Done and press ENTER. To revert to the factory defaults, highlight Reset and press ENTER.

Note:

If you select one of the factory-set picture modes (Sports, Standard, or Movie) and then set the dynamic contrast to ÒOn,Ó the picture mode automatically changes to Preference in the Picture Settings menu.

		Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.	81
			81
#01E_079-086_566272HM195	81	7/28/05, 4:51 PM
	Black

(E) 56/62/72HM195

Image 81

Contents 56HM195 62HM195 72HM195 Disposal of mercury may be regulated due to Safety PrecautionsThis TV is not Intended for USE with a PC 56HM195 ST5685 62HM195 ST6285 72HM195 ST7285Installation, Care, and Service Important Safety InstructionsFor replacement of the obsolete outlet On nextContact a Toshiba Authorized Service Center Frequent or continuous, unplug the power cordLamp in this product has a limited service life. Never attempt to service the TV yourselfContents Using the TV Guide On Screenª 103110 Features of your new TV IntroductionWelcome to Toshiba See LED indications on Install the batteries in the remote controlPower Press to turn the TV on and off Connecting your TVTV front and side panel controls and connections See LED indications on page 99 for additional informationTV back panel connections 7 !¡Computer PC. This TV is not intended for use with a PC To a Personal Computer PC Overview of cable typesFor more information, call your local cable operator ¥ In Canada, call TCL Customer Service atYou will need To view encrypted digital channelsConnecting a camcorder Connecting a VCR and antenna or Cable TV no Cable boxOn Screen recording features Connecting a VCR and Cable boxTwo sets of standard A/V cables To view basic and premium Cable channelsSelect the ColorStream HD-1 video input source on the TV Connecting a VCR and satellite receiverFrom antenna From satellite dishTo view the DVD player To view premium Cable channelsTo view antenna or Cable channels Your TV has ColorStream component video inputsSelect the ANT 1 video input source on the TV To record a TV program while watching a DVDTo view the antenna or Cable signal Connecting two VCRsSelect the ANT-1 video input source on the TV To view VCROne Hdmi cable type a connector per Hdmi device Connecting an HDMIª or a DVI device to the Hdmi inputSee ÒSetting the Hdmi audio modeÓ on To connect an Hdmi device, you will needConnecting an analog audio system Connecting a digital audio systemTV’s Digital Audio OUT terminal outputs a Dolby To control the audioTheaterNetª on-screen device control To connect the IR blaster cableTo control the devices Using analog-compatible IEEE1394 devices Connecting IEEE1394 video devicesSupported signals Using TheaterNetª on-screen device controlIEEE1394 device initialization When you connect a D-VHS or Avhd device to the TVIEEE1394 device management To edit the IEEE1394 device informationHighlight the device you want to edit and press Enter To connect to the G-LINK ª terminal LINKª connectionSee Chapter LINKª IR blaster cable wand approx inch from deviceLearning about the remote control Using the remote controlPoint remote control toward remote sensor on front of TV Remote control effective rangeInstalling the remote control batteries To install the remote control batteriesDevice mode control after programming Power Remote Control functional key chartAudio VCR Mute Device Device code setupSearching and sampling the code FunctionsOperational feature reset Using the volume lock featureRepeatedly press Mode to select CABLE/SAT mode To reset the volume controls to the original device modeVCRs/PVRs Multi-brand remote control device codesCable boxes Brand CodeReceivers CD playersLaser disks DVD playersMain menu layout Menu layout and navigationNavigating the menu system Setup / Installation menu layoutExit Menu Enter ExitSetting up the TV Guide On Screenª system TV Guide On Screen setupConfiguring the location of your TV To set up the TV Guide On Screenª systemOn next For additional details, seeSetting up the TV Guide On Screenª system TV Guide On Screenª Reminder After testing and youSetting up your TV To configure the ANT 1 and ANT 2 input sourcesTo select the menu language Programming channels into the TVÕs channel memory Programming channels automaticallyTo program channels automatically Manually adding and deleting channels in the channel memory To add and delete channels in the Favorite Channels sets To clear your favorite channel listsList Picture multi-window for the current ANT inputSetting up TheaterNet Setting up and using TheaterNetª on-screen device controlTo set up TheaterNet device control To remove a device from TheaterNetTo select the deviceÕs control icons directly Using the TheaterNet control iconsTo close the on-screen control icons To view another sourceAmplifiers TheaterNetª IR device codesLaser disk players Miscellaneous audio devicesADC Video accessory Hdtv decoder Receivers VCRsSTS Setting the HDMIª audio mode Setting the time and dateTo set the Hdmi audio mode To set the Avhd device skip timeTo set the Quick Restartª feature Setting the Quick Restartª FeatureViewing the CableCARDª menu To view the CableCARDª menuViewing the system status Restore Factory DefaultsTo open the TV Guide On Screenª system Rating, stereo, HDTV, new episodeLineup so your favorite stations are listed first Navigating the TV Guide On Screenª system TV Guide On Screenª remote control functionsMenu Info TV Guide Enter Down REC SplitVideo Window Panel MenusTo lock/unlock the Video Window TV Guide On Screenª Icons Info BoxHdtv Show is presented in high-definition TV, if availableTV Guide On Screenª Services Listings screenEpisode Options panel menu Example Category search Search screenExample Keyword search List of all matching shows for that keyword is displayedTo edit or delete a keyword Recordings screen For additional details, see ÒRecord featuresÓ onTo choose the way recordings are displayed To view a recording, you can do one of the followingRecord features Set a show to Record from a panel menuSchedule screen Record conflict Record iconsRecording notification banner Remind features Reminder notification banner Remind conflictRemind icons Setup screen Change system settingsChange channel display General defaults Change default optionsRecord defaults Remind defaultsSelecting the video input source to view Using the TV’s featuresTo select the video input source to view ¥ The source can be Òhidden.Ó See page 68 for detailsDTV Satellite/DSS Cable Game Console Labeling the video input sourcesTo label the video input sources To clear the input labelsUsing the Channel Browserª Tuning channelsTo toggle between Browse mode and Select mode To tune to a channel in Browse modeTo set a channel as Home using the remote control Setting a channel as the ÒHomeÓ channel for an inputTo set a channel as Home using the menus Adding and clearing channels in the channel historyTuning to the next programmed channel Tuning your favorite channelsSwitching between two channels using Channel Return Switching between two channels using SurfLockªNatural picture size Selecting the picture sizeYou can view many program formats in a variety of picture To select the picture sizeNone of the picture is hidden Scrolling the TheaterWide picture onTheaterWide 1 picture size For 43 format program TheaterWide 2 picture size for letter box programsTo turn on the auto aspect ratio feature To set the scroll settingsTo turn off the auto aspect ratio feature TheaterWide 2 and 3 onlyTo set the Cinema Mode to Film Selecting the lamp modeTo set the Cinema Mode to Video To select the lamp modeUsing the POP double-window feature Using the POP featuresTo display a program in the POP window To close the POP window and tune to the highlighted windowPOP double-window aspect ratio Switching the speaker audio main or POPUsing the favorite channel scan feature Using the Freeze featureTo scan and tune your favorite channels Highlight the window for the channel you want to viewAdjusting the picture Selecting the picture modeAdjusting the picture quality Selecting the color temperature Using CableClear¨ /DNR digital noise reductionCableClear/DNR field, select your desired setting To select the color temperatureUsing dynamic contrast Using Mpeg noise reductionTo select the Mpeg noise reduction level To select dynamic contrast preferencesAdvanced closed captions Using the closed caption modeTo view captions or text To view text Highlight T1, T2, T3, or T4To select digital closed captions Digital closed captionsUsing the digital audio selector Adjusting the audioMuting the sound Selecting stereo/SAP broadcastsAdjusting the audio quality Using the sub-bass system SBSUsing the StableSound¨ feature Using the SRS WOWª surround sound feature Turning off the built-in speakersSelecting the optical audio output format Media Specifications Using the media playerMemory card specifications Jpeg file specificationsMedia player specifications Using the Jpeg picture viewerDuring the slide show Using the Jpeg picture viewerTo set the slide show interval To close the picture viewerMemory card care and handling Using the MP3 audio playerTo use the mute function To close the MP3 audio playerSetting the sleep timer Setting the On/Off TimerUnderstanding the last mode memory feature Understanding the auto power off featureUsing the Gray Level feature Displaying TV setting information on-screen using RecallEntering the PIN code Using the Locks menuIf you cannot remember your PIN code Changing your PIN codeTo block and unblock TV programs and movies Blocking TV programs and movies by rating V-ChipPress z to highlight Edit Rating Limits and press Enter Edit Rating Limits screen below appearsBlocking channels Unlocking programs temporarilyLocking video inputs Using the control panel lock feature Using the GameTimerªTroubleshooting SAP mode may be on. Set the MTS feature to Stereo mode Symptom SolutionClosed caption problems Rating Blocking V-Chip problemsLED indications Setup TV Guide On Screenª FAQs101 On Screen ª system? TV Guide On Screenª FAQsLamp unit replacement and care Replacing the lamp unit When to replace the lamp unitAppendix How to replace the lamp unit Grasp the lamp unit handle and gently pull the lamp unitOr serious injury Disposing of the used lamp unit U.S., call Tacp consumer solutions at 1-800-631Edid = Enhanced-Extended Display Identification SpecificationsLimited One 1 Year Warranty on Parts and Labor Limited United States WarrantyLimited One 1 Year Warranty on Lamp Unit How to Obtain Warranty ServiceHow to Obtain Warranty Services Limited Canada Warranty109 Channel programming Index87-90 12-25Remote control Picture adjustmentsPicture-out-picture POP 10605-08 Manufactured by