LG Electronics 60LP645H, 39LP645H, 32LP645H Preventing Image burn or Burn-in on your TV, Screen

			IMPORTANT SAFETY INSTRUCTIONS	5
yyDot Defect		For USA and Canada
	The Plasma or LCD panel is a high technology
	product with resolution of two million to six million
	pixels. In a very few cases, you could see fine dots
			FCC NOTICE
	on the screen while you’re viewing the TV. Those
	dots are deactivated pixels and do not affect the	This equipment has been tested and found to
	performance and reliability of the TV.
		comply with the limits for a Class B digital device,
yyGenerated Sound
		pursuant to Part 15 of the FCC Rules. These limits
	“Cracking” noise: A cracking noise that occurs
		are designed to provide reasonable protection
	when watching or turning off the TV is generated by
		against harmful interference in a residential
	plastic thermal contraction due to temperature and
		installation. This equipment generates, uses and can
	humidity. This noise is common for products where
		radiate radio frequency energy and, if not installed
	thermal deformation is required.
		and used in accordance with the instructions, may
	Electrical circuit humming/panel buzzing: A low level
		cause harmful interference to radio communications.
	noise is generated from a high-speed switching
		However, there is no guarantee that interference
	circuit, which supplies a large amount of current
		will not occur in a particular installation. If this
	to operate a product. It varies depending on the
		equipment does cause harmful interference to radio
	product.
		or television reception, which can be determined
	This generated sound does not affect the
		by turning the equipment off and on, the user is
	performance and reliability of the product.
		encouraged to try to correct the interference by one
yyTake care not to touch the ventilation openings.
		or more of the following measures:
	When watching the TV for a long period, the
			- Reorient or relocate the receiving antenna.
	ventilation openings may become hot. This does
	not affect the performance of the product or cause		- Increase the separation between the
	defects in the product.		equipment and the receiver.
yyIf the TV feels cold to the touch, there may be a			- Connect the equipment to an outlet on a circuit
	small “flicker” when it is turned on. This is normal,		different from that to which the receiver is
	there is nothing wrong with TV. Some minute dot		connected.
	defects may be visible on the screen, appearing as		- Consult the dealer or an experienced radio/TV
	tiny red, green, or blue spots. However, they have		technician for help.
	no adverse effect on the TV’s performance. Avoid	This device complies with part 15 of the FCC Rules.
	touching the LCD screen or holding your finger(s)	Operation is subject to the following two conditions:
	against it for long periods of time. Doing so may	(1) this device may not cause harmful interference
	produce some temporary distortion effects on the	and (2) this device must accept any interference
	screen.	received, including interference that may cause
		undesired operation of the device.
	Preventing “Image burn” or “Burn-in” on your TV	Any changes or modifications in construction of
		this device which are not expressly approved by
	screen
		the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE TO CABLE/TV INSTALLER

ENGLISH

yyIf a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is “image burn” or “burn-in” and not covered by the warranty.

yyIf the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen.

yyAvoid displaying a fixed image on the TV screen for a long period of time (2 or more hours for LCD, 1 or more hours for the Plasma TV) to prevent image burn.

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.