Panasonic DMP-BDT350, DMP-BDT300 Messages, On the television, On the unit’s display

Page 37

Messages

The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use.

On the television

Cannot play.

¾You inserted an incompatible disc (Discs recorded in PAL video, etc.).

Cannot display on this unit.

¾You tried to play a non-compatible image.

¾Confirm “SD” on the unit’s display is not blinking and re-insert the card.

No disc is inserted.

¾The disc may be upside down.

$This operation is not available.

¾Some operations are unsupported by the unit. For example;

–BD-Video: During playback, reverse slow-motion or reverse frame-by-frame is not possible.

IP address is not set.

¾The “IP Address” in “IP Address/DNS Settings” is “---. ---.

---. ---”. Set the “IP Address”, “Subnet Mask”, and “Default Gateway”. (Select the automatic address acquisition if necessary.)

The current security setting of Wireless LAN is low. It is recommended to change the setting. [BDT350]

¾Authentication type for the Wireless LAN is set to “Open system”, or the encryption type is set to “No encryption”. It is recommended to encrypt for safety reasons. For details, refer to the instructions of the Wireless router being used. Encryption is required when playing back video, etc., from DLNA compatible devices.

On the unit’s display

F99

¾The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to standby for 3 seconds. Now press [POWER Í/I] on the main unit again to turn the unit on.

HDMI ONLY

¾Some BD-Video discs can only be output with HDMI.

NET

¾Displays while VIERA CAST is starting up.

No PLAY

¾There is a viewing restriction on a BD-Video or DVD-Video. (> 30)

No READ

¾The media is dirty or badly scratched. The unit cannot play.

PLEASE WAIT

¾The unit is carrying out an internal process. This is not a malfunction. You cannot operate the unit while “PLEASE WAIT” is displayed.

REMOVE

¾The USB device is drawing too much power. Remove the USB device.

SET 

(“ ” stands for a number.)

¾The remote control and main unit are using different codes. Change the code on the remote control.

Press and hold [OK] and the indicated number button at the same time for more than 5 seconds.

U59

¾The unit is hot.

The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears.

Select a position with good ventilation when installing the unit. Do not block the cooling fan on the rear of the unit.

U72

U73

¾The HDMI connection acts unusually.

–Turn the unit and TV off.

–Disconnect the HDMI cable between the player and the TV.

Hor F

(“ ” stands for a number.) ¾ There is something unusual.

¾ Check the unit using the troubleshooting guide. If the service number does not disappear, do the following.

1 Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.

2Press [POWER Í/I] to turn the power on.

If the service number does not disappear despite doing the above, request service from the dealer. Inform the dealer of the service number when requesting service.

START

¾The system is being restarted during the firmware update. Please do not turn off power.

UPD/

(“ ” stands for a number.)

¾The firmware is being updated. Please do not turn off power.

FINISH

¾ The firmware update is complete.

Reference

37

VQT2J87 (ENG)

Page 36 Page 38
Image 37
Page 36 Page 38
Contents If you have any questions contact Model No. DMP-BDT300Following Applies only in the U.S.A. FCC Note Important Safety InstructionsTable of contents Using the remote control AccessoryUnit and media care Control reference guide Power button Power Í/IFront panel Playable discs/Cards/USB devices Type Logo examples Type detail Playable contentsRegion management information Discs that cannot be played in this unitFinalize BD-VideoHighest Quality Video Connecting to a TVStandard Quality Video Audio/Video Component CableDigital Audio Connecting to an amplifier/receiverHdmi cable Multi channel speakers Amplifier/receiver Multi channel speakers Amplifier/receiverConnect Audio cables to Analog AudioTerminals corresponding To the speakers you have Connected Cable connectionsLAN Cable Broadband router, etc Connecting to a broadband networkDlna Certified media ServerFollowing Applies in the U.S.A. and Canada Precautions of Wireless LAN AdaptorSetting Connecting to an AC powerEasy Setting Press Í PowerSelect Wired or Wireless and press OK Network Easy SettingFor wireless LAN connection Access Point Connection SettingConnection to access point LAN IP address setting Fail Network Easy Setting Connection CheckNetwork Easy Setting Internet Connection Check DisplayFirmware updates Reprogramming the remote controlFor other Panasonic products Inserting or removing media To switch drivesFunctions menu Playing video contents Press SUB Menu Select an item, then press OK Useful functionsPress PIP Deleting data/Formatting SD cardsConnect to the network Insert the discRegarding DivX Cancel the unit’s registrationDisplaying subtitle text Set Subtitle in DiscEnjoying 3D video To show the picture properties Playing still picturesInsert a disc, SD card or USB device Press 3, 4, 2, 1 to select the album and press OKEnjoying Viera Casttm Playing musicPlaying a track in another folder Useful functions for when playing back pictures Dlna feature BDT350While contents list is displayed StatusLinked operations with Easy control only with Viera remote controlTV Viera LinkTM Hdavi ControlTM Viera LinkTM is a new name for EZ SyncTMDisc Playback menuVideo PlayAudio Setup menu Display TV / Device Connection Others NetworkGeneral operation Troubleshooting guideCannot eject disc Picture Playback On the television MessagesOn the unit’s display About audio from audio output terminals Audio InformationHdmi AV OUT/DIGITAL Audio OUT Coaxial/Optical Press Setup Audio Set each item Recommended audio output settingFor details of the each item, refer to Stereo*5DivX About MP3/JPEG/DivX/ AVCHD/MPEG2 filesSubtitles text file of DivX Structure of folders that can be played in this unit Supplemental information Specifications Contact Information cdrequest@am-linux.jp Glossary As of November Product or Part Name Parts LaborLink ServicentresTM locator under Customer support Limited Warranty Only for CanadaFor Product Operation ASSISTANCE, please contact Conexiones básicas Referencia rápida enReproducción básica Off Timer On-screen Language Picture-in-picture Playback AC Power Connection Angle AudioIndex Local storage M MPEG2 MP3 Network
Top Page Image Contents