**If Source Stream is 2ch,
of the main feature.
Navigation Sound Effects are different on each Blu-ray Disc.
✎✎ NOTES
`` Be sure to select the correct Digital Output or you will hear no sound or just loud noise.
`` If the HDMI device (AV receiver, TV) is not compatible with compressed formats (Dolby Digital, DTS), the audio signal outputs as PCM.
`` Regular DVDs do not have BONUSVIEW audio and Navigation Sound Effects.
`` Some
`` If you play MPEG audio soundtracks, the audio signal outputs as PCM regardless of your Digital Output selections (PCM or Bitstream).
`` If your TV is not compatible with compressed
`` If your TV is not compatible with PCM sampling rates over 48kHz, the player may output 48kHz downsampled PCM audio even though you set PCM Downsampling to Off.
PCM Downsampling
Lets you choose to have 96KHz PCM signals downsampled to 48KHz before they are outputted to an amplifier. Choose only if your amplifier or receiver is not compatible with a 96KHz signal.
Dynamic Range Control
Lets you apply dynamic range control to Dolby Digital, Dolby Digital Plus, and Dolby True HD audio.
•Auto : Automatically controls the dynamic range of Dolby TrueHD audio, based
on information in the Dolby TrueHD soundtrack.
Also turns dynamic range control on for Dolby Digital and Dolby Digital Plus.
•Off : Leaves the dynamic range uncompressed, letting you hear the original sound.
•On : Turns dynamic range control on for all three Dolby formats. Quieter sounds are made louder and the volume of loud sounds is reduced.
Downmixing Mode
Lets you select the
Network Settings
Please contact your ISP to find out if your IP address is static or dynamic. If it is dynamic - and most are - we recommend using the Auto procedure for network setup. This is easiest and will work in the majority of cases. If it is static, you must use the manual set up procedure.
Network setup directions start below. ✎✎ NOTES
`` This unit can only be connected to a Network via a wired connection.
Wired Network Settings
1.In the Home menu, press the ◄► buttons to select Settings, and then press the v button.
2.Press the ▲▼ buttons to select Network, and then press the v button.
3.Press the ▲▼ buttons to select Wired Network Settings, and then press the v button. The Wired Network Settings screen appears.
Settings
Display |
| Wired Network Settings |
|
| |||
Audio | Internet Protocol Setup : Auto |
|
| \ | |||
Network | IP Address | : | 0 | 0 | 0 | 0 | |
System |
| Subnet Mask | : | 0 | 0 | 0 | 0 |
Language Gateway | : | 0 | 0 | 0 | 0 | ||
SecurityDNS | : Auto | 0 | 0 | 0 | |||
General |
| DNS Server | : | 0 | |||
Support |
| > Move " Select ' Return | |||||
4.In the Internet Protocol Setup field, select Auto if it is not selected. (Press v to select Auto, and then press v.)
5.The Auto Function acquires and fills in the values for IP Address, Subnet Mask, etc., automatically.
✎NOTES✎
`` This process can take up to five minutes.
6.After the Network Function has acquired the network values, press the RETURN button.
7.Select Network Test, and then press v to ensure the player has connected to your network.
8.When the Network Test is complete, press the RETURN twice to return to the Main Menu.
9.If the Network Function does not acquire the network values, go to the directions for Manual Setup.
Manual Network Setup
Before you start manual network setup, you need the network setting values.
To get the network setting values, contact your ISP (Internet Service Provider) or your network administrator.
To enter the Network Settings into your player, follow these steps:
1.In the Home menu, press the ◄► buttons to select Settings, and then press the v button.
2.Press the ▲▼ buttons to select Network, and then press the v button.
11