Pioneer BDP-LX08 operating instructions Troubleshooting, Playback

Page 51

Chapter 7

07

Additional information

 

Troubleshooting

Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified even after checking the points below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

Playback

Problem

Check

Remedy

Disc does not play.

Is the disc scratched?

It may not be possible to play scratched discs.

Disc tray opens

 

 

Is the disc dirty?

Clean the disc (page 59).

automatically.

 

 

Is the disc properly set in the disc tray?

• Set the disc with the printed side facing up.

 

 

 

• Set the disc properly in the depression in the disc tray.

 

 

 

 

Is the region number correct?

The region numbers of discs that can be played on this set are

 

 

as shown below (page 9).

 

 

• BDs: “B” (or including “B”) and “ALL”

 

 

• DVDs: “2” (or including “2”) and “ALL”

 

 

 

 

Is the player set in a humid place?

There could be condensation inside. Wait for the condensation

 

 

to dissipate. Do not set the player near an air-conditioner, etc.

 

 

(page 58).

 

 

 

Picture freezes and the front

 

• Press  STOP to stop playback, then restart playback.

panel and remote control

 

• If the playback cannot be stopped, press  STANDBY/ON

buttons stop working.

 

on the player’s front panel to turn off the power, then turn the

 

 

power back on.

 

 

• If the power cannot be turned off, press and hold

 

 

STANDBY/ON on the player’s front panel for over 5

 

 

seconds. The power will turn off.

 

 

 

No picture is displayed or the

Is the video cable properly connected?

Insert the cable firmly and all the way in.

picture is not displayed

 

 

Is the video cable damaged?

If the cable is damaged, replace it with a new one.

properly.

 

 

 

Is the input setting on the connected TV or AV receiver or

Read the operating instructions of the connected components

 

amplifier right?

and switch to the proper input.

 

 

 

 

Are the terminals for outputting video signals properly set?

Press VIDEO SELECT to switch the terminal from which the

 

 

video signals are output.

Is the output video resolution properly set?

Depending on the player’s output video resolution, the picture may not be displayed at all or displayed properly. Use OUTPUT RESOLUTION to switch to a resolution at which the picture is displayed properly (page 24).

 

Is the player connected with an HDMI cable other than a High

Press  STOP while pressing  PLAY on the player’s front

 

Speed HDMI™ cable (with a Standard HDMI™ cable)?

panel to restore the video outputs to the factory default

 

 

settings. After this, use the Setup Navigator to reset the player.

 

 

 

 

 

There are some BDs for which the picture will only be output

 

 

when connected by HDMI cable.

 

 

 

 

Does the connected TV support the frame rate of the video

If the picture is not displayed when playing a disc with a frame

 

signal being output by the player?

rate that is not supported, the picture will not be displayed even

 

 

when playback is stopped.

 

 

In this case, use the procedure below to switch the frame rate

 

 

of the video signals output from the player. Eject the disc and

 

 

close the disc tray. Then, press OPEN/CLOSE while pressing

 

 

PLAY on the player’s front panel to switch to a frame rate

 

 

supported by the connected TV.

 

 

 

 

Is NTSC on PAL TV properly set?

Set NTSC on PAL TV properly (page 41).

 

 

 

51

En

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Blu-ray Disc Player Operating Environment  For U.K model For batteries Symbol examplesContents Insert the batteries AA/R6 x Putting the batteries in the remote controlWhat’s in the box Open the rear coverNon-finalized Dual Layer DVD-R discs in the DVD VR format Types of discs/files that can be playedPlayable discs  Discs that cannot be played About audio formats  Playing BDs Playing DVDs Playable files Movie files Part Names and Functions Playable file extensions MPEG-1 Audio Layer 3 MP3Tools Front Panel Display Front PanelHdmi OUT terminal Audio OUT 2 ch terminalsAudio OUT 7.1 ch terminals Video OUT terminals About Hdmi Connecting a TVConnecting using a commercially available Hdmi cable Hold the plug when connecting and disconnecting the cable About Hdmi Control function  When connected to a DVI device About the Hdmi high speed transmission  About HdcpPlayer’s rear panel Connecting using a commercially 02 available Hdmi cable Connecting an AV receiver or amplifierPlayer’s rear panel Connecting using audio cablesConnecting the power Cord Turn on the TV’s power and switch the input Making settings using the Setup Navigator menu If the Setup Navigator menu is not displayed Turn on the power. Press  STANDBY/ONUse / to select Yes, then press Enter Check the settings Select Proceed, then press EnterFinish the Setup Navigator menu Output test tonesOperating the TV with the player’s remote control TV Preset code list03  About the screen saver Display the Tools menu Using the Tools menu To close the Tools menu  Tools menu item listErase the data Switching the output video resolution Press Output Resolution Select and set the item About the frame/field frequency and NTSC/ PAL TV systems  About Film material To output film material  To resume normal playback Playing discs or filesForward and reverse scanning  If the disc menu is displayedStep forward and step reverse Skipping contentPlaying specific titles, chapters or tracks Playing in slow motion Turning the subtitles off Switching the camera anglesSwitching the subtitles Switching the audio streams/ channelsPlaying from a specific time Time Search Using the Play Mode functionsSwitching the secondary video Displaying the disc information To cancel Time Search  To cancel the searchPlaying a specific title, chapter or track Search Select Repeat/Random  To cancel A-B Repeat play To cancel Repeat Play Select A-B Repeat To cancel Random Play Playing in random order Random PlaySelect the Random Play Playing a specific section within a Repeat play Random Search play Closing the Home Media Gallery Playing from the Home Media GalleryPlaying discs Playing movie filesSelect Folders or All Songs Playing music filesSelect Movies Select MusicIf you have selected All Songs, proceed to step Playing in the desired order HMG Playlist Adding tracks/files All Songs All the recorded files are displayedSelect HMG Playlist Use / to select, then press Enter  Playing the HMG Playlist Deleting tracks/files from the HMG Playlist Press Tools to display the Tools menu When Memory1, 2 or 3 is selected Adjusting the video Closing the Audio DRC screen Adjusting the Audio DRC Closing the Video Adjust screen  About Pure CinemaSelect and set Initial Setup Changing the settings Initial SetupOperating the Initial Setup screen  Closing the Initial Setup screenSelect this when multi-system NTSC-compatible TV Device connected using an Hdmi cable Select this when connected with a Standard Hdmi cableEnables Pqls function Off Disables Pqls function Hdmi ControlChange the language Changing to other language at language setting To change the language using numbers Select and set OtherSelect and set Speakers Changing the speaker setup Closing the speaker settings screen Select the speaker and change the setting Closing the Channel Level screen Registering or Changing the passwordAdjust the output level Re-input the passwordChange the age Changing the Age Restriction for watching BD-ROMs To change the code number Select and set Parental LockUse / to change, then press Enter to set Changing the Parental Lock level for watching DVDsPress Enter to set Use / to move the cursor Change the level To change the country/area code using numbers Changing the Country/Area codeChange the country/area code Restoring all the settings to the factory default settings Set the video and audio terminals to be usedSelect and set Options About the audio output settings Playback TroubleshootingOutput from the Hdmi OUT terminal or the Component Ch terminals page 41. Set Audio Output Mode toAre the speakers properly set? Set Speaker Setup properly Picture is stretched Is the TV’s aspect ratio properly set?Sound is fast or slow KHz for outputSecondary audio or Is Hdmi Audio Out properly set? Interactive audio is notWhen connected using an Hdmi cable Others Language Code Table and Country/Area Code Table Language Code TableCountry/Area Code Table Specifications Cleaning the pickup lens Place of installationTurn the power off when not using the player Cleaning the player Condensation on discs  Cleaning discs Storing discs  Specially shaped discs DivX  DTS-HD High Resolution Audio Hdcp High-bandwidth Digital Content Protection 07  Deep Color Secondary video  Region number S-Video output  Secondary audio zlib  FreeType2 Licenses libxml2  OpenSSL libpng References  libjpgReferences Archive Locations  AVC/H.264No Warranty  GNU Lesser General Public License Page How to Apply These Terms to Your New Libraries Page Pioneer Corporation
Top Page Image Contents