Arcam BDP300 manual Customising CR104, Code learning

Page 26

customising

the CR104

Code learning

The CR104 comes with a complete library of preprogrammed codes. After you have set up the CR104 for your device, you may find that there are one or more functions on your original remote which do not have a place on the CR104 keypad. For convenience, the CR104 offers a Code Learning feature that allows you to copy up to 16 functions from an original remote control onto the CR104 keypad.

Before you start, make sure that:

<<The original remote control is working correctly.

<<The remotes are not pointing at your device.

<<The remotes have new batteries.

<<The remotes are not in direct sunlight or under strong fluorescent lights.

NOTE

Learned functions are mode-dependent: You could theoretically assign up to eight different functions to a single key (the CR104 can handle a total of 16 learned functions).

Example: To copy the ‘text hold’ function from a TV remote onto the (key of your

CR104

1.Place both remotes on a flat surface, 2 to 5cm apart, with the IR ports facing each other.

2.On the CR104, press and hold Suntil the power LED blinks twice: **.

3.Press 975. The power LED blinks twice:

**.

4.On the CR104, press the device key that matches the ‘source’ device (e.g. if you’re learning a TV function, press A).

5.On the CR104, press the key to which you want to assign the learned function (e.g. (). The device key blinks rapidly.

6.On the original remote, press and hold the function key that you want to learn (e.g. TEXT HOLD) until the CR104 device key blinks twice:

**.

7.If you want to learn other functions from the same source device, simply repeat steps 5 and 6 pressing the next key you want to learn.

8.To exit Code Learning mode, press and hold S

until the device key blinks twice: **.

9.To use the learned function on the CR104, press the Device Mode key, followed by the function key.

In this example, you’d press A followed by (

Shifted Learning

You can assign a learned function to a CR104 key without sacrificing its original function.

You can assign Shifted Learning functions to any key except for: Device Mode keys (e.g. A), S, or number keys (0to 9).

1.To assign a Shifted Learning function, simply follow Code Learning steps in the previous section. During step 5, press Sonce before you press the key to which you want to assign the learned function.

2.To access the shifted function, press Sand then the target key.

Important notes

<<Once you start a Code Learning session, you have approximately 10 seconds to conduct each step. Any longer, and a timeout means that you’ll have to start the process again.

<<The Learning feature is mode-specific – you can copy one feature per mode onto a key.

<<The CR104 can learn approximately 16 functions in total.

<<To replace a learned function, simply assign a new one to the same key.

<<Learned functions are retained when you change batteries.

<<If Code Learning fails, try altering the distance between the two remotes; make sure that the light in the area is not too bright.

To delete a learned function

1.Press and hold Suntil the power LED blinks twice: **.

2.Press 976. The power LED blinks twice:

**.

3.Press a Device Mode key once. For example, if you want to delete one of your learned TV functions, press A.

4.Press twice on the key you want to deassign. The handset blinks twice: **to confirm.

The original function of the CR104 is restored.

To delete a Shifted Learned function:

To delete a Shifted Learned function, press Sbefore you press the key to be deassigned (during step 4 above).

To delete ALL learned functions within a given Device Mode

1.Press and hold Suntil the power LED blinks twice: * *.

2.Press 976– the power LED blinks twice:

**.

3.Press the appropriate Device Mode key twice.

E-26

Image 26
Contents BDP300 N D B O O K Blu-ray Disc playerSafety compliance Safety GuidelinesImportant safety instructions Contents WelcomeRemote control and trigger inputs InstallationPower Placing the unitEnglish Making video connections Making audio connectionsTroubleshooting Hdmi Hdmi interfaceRegion coding Disc & file FormatsPlayable discs USB Flash Drive Network connectionUSB connection To skip chapters or tracks on a CD, press / or Basic OperationIntroduction On the front panel or 4 on the handsetUsing the remote control CR104 complies with Part 15 of the FCC rulesCR104 remote Select the source key firstPlayback and advanced controls Track optionsControlling other devices Device Mode / Source keysUseful information Code blink-back Menus Disc informationSearch Soundtrack selectionPlaying media files Rapid Playback Advanced playback controlsSlow playback Displaying File InformationDisplay Settings MenusEntering the settings menu Navigating the menusYou can select AudioWe recommend you select ‘Auto’ Language NetworkAfter it has loaded SystemSecurity/Parental Control English Sometimes a small amount of picture distortion may Power switch again and then unload the discSet the resolution correctly see page E-19 Appear. This is not a malfunctionAudio Audio output formatCustomising CR104 Code learningKey mover Volume punch-throughCreating Macros To restore a moved Device Mode key to its original state Mode moverLocking/unlocking a specific Device Mode Copy a key between Device ModesMode key IR punch-through Resetting the CR104Laser radiation SpecificationsRadio interference Continual improvement policySoftware licencing Page Correct disposal of this product Product GuaranteeWarranty covers Device code Tables Таблицы Кодов УстройствHCM GBCGEC HYDRBM NU-TECOKI RCAGPX YU-MA-TUAVP NTL STSADB UPCAMW 3D LABAKI AtacomXMS TSMTVE AsciKPN HNEIdte SAT