BDS 270/BDS 570
Setting Up the Receiver
EZ Set/EQ: The BDS receiver’s EZSet/EQ™ system uses the supplied EzSet/EQ microphone to perform this important step automatically. Before beginning, be sure you have correctly connected your speakers to the BDS receiver. IMPORTANT: Press the remote’s “Disc” input button before performing the EZ Set/EQ procedure. The EZ Set/EQ procedure is only available when the Disc input is selected.
1. Plug the supplied EzSet/EQ microphone into the BDS receiver’s Headphone connector.
2.Place the microphone at ear height in your main listening position.
3.Press the remote control’s Home button. The receiver’s Home Menu screen will appear on the TV.
Home Menu |
|
|
| ||
|
|
|
|
|
|
|
| FM Radio |
|
|
|
|
| HDMI input |
|
| Type: Settings |
|
| Component input |
|
| |
|
|
|
|
| |
|
| Playlist |
|
|
|
|
| Settings |
|
|
|
1 | / | 5 | HOME | Exit | OPTIONS Option |
6.Press the right Cursor button to select EzSet/EQ, then use the cursor buttons to select the configuration of your speaker system.
Audio Settings
Tone Controls | EzSet/EQ | Off |
Audio Output | Manual Configuration | 2.0 |
Speaker Settings |
| 2.1 |
|
| 3.1 |
|
| 5.1 |
The EzSet/EQ automatic setup can calibrate the BDS system and configure the loudspeakers parameters automatically to get the best sound performance.
7.Press the OK button, then press it again to select Continue in the EzSet/EQ (Automatic Setup) box that appears.
Audio Settings
EzSet/EQ(Automatic Setup) |
| Off | |
Tone Controls | EzSet/EQ |
| |
| Please plug the microphone into the system and | ||
Audio Output | then place it at ear leve at yo | desired listening | |
Manual Configuration | 2.0 | ||
| position. If a Subwoofer is connected, set the level | ||
| control (on the Sub) to half. |
| 2.1 |
Speaker Settings |
| ||
| Continue | Cancel | 3.1 |
5.1
The EzSet/EQ automatic setup can calibrate the BDS system and configure the loudspeakers parameters automatically to get the best sound performance.
4.Use the Cursor and OK buttons to highlight and select Settings. The General Settings menu will appear.
8.Remain silent while the test noise plays through the speakers. As the test noise circulates among the speakers the screen will show which speaker is being tested.
General Settings
System
Language
Playback
Parental Control
Network
Select to adjust general settings
5.Use the right Cursor button to select Audio Settings, then use the down Cursor button to select Speaker Settings. The Speaker Settings screen will appear.
Audio Settings
Tone Controls | EzSet/EQ | 2.0 |
Audio Output | Manual Configuration | 2.0 |
Speaker Settings |
|
|
Select to adjust speaker settings
Audio Settings
EzSet/EQ(Automatic Setup) |
|
|
| C |
|
| L |
|
| R | |
|
|
|
| ||
Testing... | LS |
|
|
| RS |
|
|
|
|
|
|
Please keep room silent. |
| SUB |
| ||
|
|
|
|
| |
The current testing speaker is L
9.When the testing process is completed, the “Testing...” message on the screen will change to “All test done!”
10.Press the Clear/Exit button to exit the EzSet/EQ test procedure.
NOTE: If the test fails, the “Testing...” message on the screen will change to “Test failed, please make sure the speaker is connected correctly and room is silent, then retest.” Press the Clear/Exit button, make sure all speakers are correctly connected and perform the test again from Step 6. Make sure that the room remains silent during the test.
18