Audiovox APS57 installation manual 128-7767

Page 4

Action

System Response

No response

 

Turn ignition on

 

Press and release the valet switch 3 times

1 Chirp - LED 1 flash

 

Within 3 seconds, turn ignition Off, On, Off, On

Short chirp, then 2 long chirps

 

This Action Accesses Feature Bank 3 Remote Start Selectable Features

First

Press the valet switch one time

1 chirp = defrost output pulsed

 

Press transmitter Lock button to change

2 chirps = defrost output 10 Mins

Second

o r

2 chirps = RF start chirp on

Press and release the valet switch

 

Press transmitter Lock button to change

1 chirp = RF start chirp off

Third

o r

2 chirps = run time set for 10 mins

Press and release the valet switch

 

Press transmitter Lock button to change

3 chirps = run time set fro 15 mins

 

Press transmitter Lock button to change

4 chirps = run time set for 20 mins

 

Press transmitter Lock button to change

1 chirp = run time set for 5 mins

Fourth

o r

1 chirp = parking lights on steady w/RS active

Press and release the valet switch

 

Press transmitter Lock button to change

2 chirps = parking lights flashing w/RS active

Fifth

o r

2 chirps = tachometer input checking

Press and release the valet switch

 

Press transmitter Lock button to change

1 chirp = voltage sense input checking

Sixth

o r

1 chirp = greater than 0.5 V check before start

Press and release the valet switch

 

Press transmitter Lock button to change

2 chirps = less than 0.5 V check before start

Seventh

o r

2 chirps = ign 2 on during crank

Press and release the valet switch

 

Press transmitter Lock button to change

3 chirps = ign 2 same as accessory

 

Press transmitter Lock button to change

1 chirp = ign 2 off during crank

Eighth

o r

2 chirps = ign 3 on during crank

Press and release the valet switch

 

Press transmitter Lock button to change

3 chirps = ign 3 same as accessory

 

Press transmitter Lock button to change

1 chirp = ign 3 off during crank

Ninth

o r

1 chirp = diagnostics off

Press and release the valet switch

 

Press transmitter Lock button to change

2 chirps = diagnostics on

Tenth

o r

2 chirps = crank time 1.0 sec

Press and release the valet switch

 

Press transmitter Lock button to change

3 chirps = crank time 1.5 sec

 

Press transmitter Lock button to change

4 chirps = crank time 2.0 sec

 

Press transmitter Lock button to change

1 chirp = crank time 0.8 sec

Eleventh

o r

1 chirp = unit set for gasoline engine

Press and release the valet switch

 

Press transmitter Lock button to change

2 chirps = unit set for diesel engine 10 sec delay

 

Press transmitter Lock button to change

3 chirps = unit set for diesel engine 15 sec delay

 

Press transmitter Lock button to change

4 chirps = unit set for diesel engine 20 sec delay

Twelfth

o r

1 chirp = transponder output while R/S active

Press and release the valet switch

 

Press transmitter Lock button to change

2 chirps = transponder output during start only

 

Press transmitter Lock button to change

3 chirps = transponder output until ignition turned off

 

o r

 

Thirteenth

Press and release the valet switch

Non Functional On This Unit

Fourteenth

o r

1 chirp = crank averaging w/voltage input checking

Press and release the valet switch

 

Press transmitter Lock button to change

2 chirps = preset crank time w/voltage input check

 

o r

 

Fifteenth

Press and release the valet switch

Non Functional On This Unit

 

o r

 

Sixteenth

Press and release the valet switch

Non Functional On This Unit

Seventeenth

o r

1 chirp = aux o/p Black/Blue single pulse

Press and release the valet switch

 

Press transmitter Lock button to change

2 chirps = aux o/p Black/Blue as alarm feature #1

Press and release the valet switch or turn the ignition off to:

Exit Programming Mode

Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps or the

programming will be terminated.

4

128-7767

4 of 19

Image 4
Contents Installation Manual Model APS-57To program these selectable features 128-7767 3 128-7767 PUSH-BUTTON LED Switch Hood PIN SwitchControl Module RECEIVER/ANTENNAASSEMBLY Wiring the 6 PIN Main Power HarnessFused RED w/ White Trace Wire + 12 volt Battery 1 Source P O R T a N TSee Neutralstart Safety Test for Further Details Gray w/ Black Tracer Wire Negative Inhibit Input Wiring Connections 12 Pin Input / Output HarnessBrown w/ Black Tracer Wire Positive Inhibit Input Brake Switch Positive Shutdown Detail White Wires Parking Light FlasherGeneral Motors Vats By-Pass Diagram Green/Orange Wire Tach Sensor InputWiring the 4 PIN Auxiliary Output Harness Tachometer Input Wiring DetailPin Door Lock/Unlock Harness White Connector Wire Ground Switched Door Lock Circuits Wire Ground Switched Door Lock/Unlock Wiring DetailWire Positive Switched Door Locks Pin Antenna/Receiver Connector White Connector Pin Blue Connector Programming SwitchMulti Coil Pack Adapter Optional Hood PIN Safety Shut Down Testing Your InstallationR N I N G Mechanical Neutral Safety Switch Considerations KEY in Sensor Circuits MethodMethod Completing the Installation Audiovox Electronics Corp., Hauppauge, NY