Hearth and Home Technologies RCT-MLT-II operating instructions General Information

Page 8

6.Advance the SET temperature on the transmitter to a temperature of at least 2º F (1º C) above the ROOM temperature displayed on the LCD screen and the system flame will ignite.

7.Set the SET temperature to at least 2º F (1º C) below the room temperature and the system flame will extin- guish. Thereafter, it should continue to cycle on and off thermostatically approximately every two minutes as the ROOM temperature changes, but only when the temperature differential between ROOM and SET temperatures differs at least 2º F (1º C). The 2º F dif- ferential is the factory setting.

Electronic Ignition System

1.Slide the 3-position button on the remote receiver to the ON position. The spark electrode should begin sparking to ignite the pilot (the pilot may ignite after only one spark). After the pilot flame is lit, the main gas valve should open and the main gas flame should ignite.

2.Slide the button to OFF. The main gas flame and pilot flame should BOTH extinguish.

3.Slide the button to REMOTE (the center position).

4.Then press the MODE button on the transmitter to change the system to ON. The spark electrode should begin sparking to ignite the pilot. After the pilot is lit, the main gas valve should open and the main gas flame should ignite.

5.Press the MODE button on the transmitter to OFF. The main gas flame and pilot flame should BOTH extinguish.

6.Press the MODE button on the transmitter to change the system to THERMO.

7.Advance the SET temperature on the transmitter to temperature of at least 2º F (1º C) above the room temperature displayed on the LCD screen and the system flame will ignite.

8.Set the SET temperature to at least 2º F (1º C) below the room temperature and the system will extinguish. Thereafter, it should continue to cycle on and off thermostatically approximately every two minutes as the ROOM temperature changes, but only when the temperature differential between ROOM and SET temperatures differ at least 2º F (1º C). The 2º F dif- ferential is the factory setting.

Timer Operation

The countdown timer will operate in either the manual ON or THERMO mode. Once the fireplace system is in an operating mode, set the countdown timer to turn off in 15 minutes. The timer function will allow operation to continue until the “countdown time” on the LCD screen expires. After 15 min. elapses, the system should turn off.

GENERAL INFORMATION

Transmitter Wall Bracket

The transmitter can be hung on a wall using the bracket provided. Locate the bracket on an inside wall suffi- ciently far away from direct sources of heat such as a fireplace, incandescent lighting, or sunlight so it detects ambient room temperatures, not a single heat source. If the bracket is installed on a solid wood wall, drill 1/8” pilot holes and install with the screws provided. If it is installed on a plaster/wallboard wall, first drill two 1/4” holes into the wall, then use a hammer to tap in the two plastic wall anchors flush with the wall, then install the screws provided.

Battery Life

Life expectancy of the batteries in the transmitter should be at least 12 months. Check batteries annually. When the transmitter no longer operates the remote receiver from a distance it did previously (i.e., the transmitter’s range has decreased) the batteries should be checked.

Specifications

Batteries: Transmitter - 3V 2 ea.; AAA 1.5V, Alkaline

Remote - 110-120 VAC; 60Hz Operating Frequency: 303.8 MHZ FCC ID No.’s: Transmitter - K9L300ITX

Receiver - K9L3003RX Canadian ISC ID No.’s: Transmitter - 2439 102 760

Receiver - 2439 102 760A

Service Parts List

DESCRIPTION

SERVICE PART NO.

3-PRONG ADAPTER

HTI-18-006

SOLENOID-110 VOLT HI/LO

HTI-17-006

TRANSMITTER WALL HOLDER

HTI-16-006

BATTERIES-TRANSMITTER

HTI-14-006

RECEIVER

HTI-13-006

TRANSMITTER (RCT-MLT-HNG)

HTI-12-006-HNG

TRANSMITTER (RCT-MLT-HTL)

HTI-12-006-HTL

HARDWARE PACKAGE

HTI-11-006

Limited Warranty

This REMOTE CONTROL SYSTEM is warranted for 12 months from the date of purchase or installation to the original purchaser to be free from defects in materials and workmanship. Damage to the SYSTEM caused by accident, misuse, abuse, or installation error whether performed by a contractor, service company, or owner, is not covered by this warranty. Seller will not be responsible for labor charges and/or damage incurred in installation,

repair, replacement or for incidental or consequential damages. Batteries and any damage caused by them are not covered by this warranty.

Some states, provinces, and nations do not allow exclu- sion or limitations of incidental or consequential damages, so the above limitations or exclusions may not apply. This warranty gives you specific legal rights. You may have other rights that vary by state, province or nation.

8

Image 8
Contents Canadian Equipment Requirements Installation PrecautionsIntroduction Remote Receiver Installation InstructionsReceiver Wiring Instructions Installing Flame Control Solenoid Transmitter Remote ReceiverTransmitter Settings Setting the ClockMatching Security Codes Operating InstructionsSetting ºF/ºC Scale Setting Desired Room Temperature Thermo OperationsSetting the Countdown Timer Operating the Fan Operates in on or Thermo modeTransmitter Safety Features System CheckGeneral Information Intermittent Pilot Ignition IPI Wiring Diagram Can be Remote Control Wiring Diagrams