Grundig CP-X385W Using the Remote Control, Putting batteries into the remote control unit

Page 13
approximately 3 meters
approximately 3 meters

USING THE REMOTE CONTROL

Putting batteries into the remote control unit

CAUTION Precautions to observe in regards to the batteries

Always handle the batteries with care and use them only as directed. Improper use may result in battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

Keep the battery away from children and pets.

Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.

When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).

When you dispose the battery, you should obey the law in the relative area or country.

1

Remove the battery

 

2

Insert the batteries

cover

 

Align and insert the two AA

 

Push the knob while lifting

 

 

batteries (that came with the

 

up the battery cover in the

 

 

projector) according to their plus

 

direction of the arrow.

 

 

and minus terminals (as indicated

 

 

 

 

 

 

 

in the remote control).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 Closecover the battery

Replace the battery cover in the direction of the arrow and snap it back into place.

Operating the remote control

The remote control works with both the

projector's front and rear remote sensors.

• The range of the remote sensor on the front and back is 3 meters with a 60-degree range (30 degrees to the left and right of the remote sensor).

• Since the remote control uses infrared light to send

 

30

degrees

 

30

degrees

signals to the projector (Class 1 LED), be sure to

 

 

30

 

30

 

use the remote control in an area free from

degrees

degrees

 

 

 

 

 

 

obstacles that could block the remote control's output signal to the projector.

Only use the accompanying remote control. Using other remote controls (even of similiar models) to control the CP-X385W may result in unexpected operation.

ATTENTION Precautions to observe when using the remote control

Do not drop or otherwise expose the remote control to physical impact.

Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.

Remove the batteries from the remote control and store them in a safe place if you won't be using the remote control for an extended period.

Replace the batteries whenever the remote control starts to malfunction.

When strong light, such as direct sunlight or light from an extremely close range (such as from an inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to function. Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.

13

Image 13
Contents Contents Ultra High Brightness Projector FeaturesConnect your devices to the projector Projector Part NamesRemote Control Angle Adjustment Setting UP the ProjectorIf 43 aspect ratio Adjusting the Screen Size and Projection DistanceConnecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesConnecting to a VCR Connecting to a DVD PlayerConnecting to a Display Monitor Putting batteries into the remote control unit Using the Remote ControlOperating the remote control Turning on the Power Selecting an Input Signal Turning OFF the Power Press the Volume button Adjusting the VolumePress Buttons to adjust Volume Temporarily Muting the SoundUse Buttons to adjust Position Adjusting the PositionPress the Position button Automatic Adjustment for RGB Input Using the Automatic Adjustment FeatureAutomatic Adjustment for Video Input Press the Auto buttonPress the Keystone button Correcting Keystone DistortionsFreezing the Screen Using the Magnify FeatureSelecting the Aspect Ratio Signal SearchingTemporarily Blanking the Screen Select a menu using Buttons Then press Or Enter button Using the Menu FunctionsSelect an item using Buttons, then press Or Enter button Press Buttons to adjust the levelPS/2, ADB, Serial Mouse Control Operating the PC ScreenLamp High Voltage High Temperature High PressureReplacing the lamp LampCaring for the air filter AIR FilterReplacing the air filter Other Care HandleFixing the Handle