Samsung ST65W3PC, ST62T8PC, ST47W3PC Memorizing the Channels, Selecting the Video Signal-source

Page 30

O P E R AT I O N

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH and CH but- tons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system).

1

Press the Menu button.

Press the CH button to select “Channel”, then press the VOL + button.


						Channel

				Antenna		: A
				ANT/CATV		: ANT
				Auto Program
				Fav. Channel
				Fine Tune		: 00
				Add/Erase
				Labeling		: - - - -

2

Press the CH button to select “ANT/CATV”, then Press the VOL + or VOL - button to cycle through these choices:

ANT (antenna), STD, HRC or IRC.


						Channel
				Antenna		: A
				Antenna		: A
				ANT/CATV		: ANT
				Auto Program
				Fav. Channel
				Fine Tune		: 00
				Add/Erase
				Labeling		: - - - -

Note: STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area.

At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (next page).

3.8 CHAPTER THREE: TV OPERATION

Image 30

Contents Owner’s Risk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding Safety Installation Your New TVOperation Special Features TroubleshootingList of Features Chapter OneFamiliarizing Yourself with The TV ´ Video Input jack Using the Component ShelfSide Panel Jacks Audio Input jacks´ AUDIO-VIDEO Monitor Output jacks Rear Panel Jacks Depending on the modelAntenna terminals ¨ Audio Input jacks Video Input jacks´ +100 Remote ControlPower StillMain¸ P.Mode ˘ R.surf¿ S.Mode ˛ VCR controlsConnecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin LeadsSeparate VHF and UHF Antennas Connecting Cable TVAntennas with 75-ohm Round Leads Cable without a Cable BoxThis terminal might be labeled Connecting to a Cable Box that Descrambles Some ChannelsCable with a Cable box that Descrambles All Channels ANT IN, VHF IN, or simply,Install AT I O N Connecting a VCR Connecting a Camcorder Connecting a Second VCR to Record from the TVConnecting a DVD Player, DTV Set-Top Box 480i, 480p Connecting to Y, PB, PRConnecting a DTV Set-Top Box 480p Installing Batteries in the Remote Control Install two AAA size batteries Replace the coverMake sure to match the + Press the Power button Plug & Play FeatureYou can also use the Power button on the front panel Turning the TV On and OffCH or CH button. refer to Setting the clock on 1Press the Menu buttonRefer to Auto program on Using the Perfect Focus Feature You can also select PerfectFocus by pressing the Perfect Focus button Adjusting Manual Convergence Adjust Red Convergence If a horizontal red line is visible, useViewing the Menus and On-Screen Displays Viewing the MenusViewing the Display Selecting a Menu Language Selecting the Antenna InputPress the VOL + or VOL button to select a or B Selecting the Video Signal-source Memorizing the ChannelsANT antenna, STD, HRC or IRC Storing Channels in Memory Automatic Method TV automatically cyclesAdding and Erasing Channels Manual Method Using the Previous Channel Using the Channel ButtonsUsing the Number Buttons Changing ChannelsCan be set as Favorite channels Selecting Your Favorite ChannelsTo Store Your Favorite Channels To View Your Favorite ChannelsAdding and Erasing Channels Manual Method Press CH or CH to tune to the channel that will be labeled Labeling in the A/V modeLabeling the Channels Select Channel, thenCustomizing the Picture After adjusting an item,Picture Control Gauge will automatically disappearafter about 4 secondsUsing Automatic Picture Settings Press the Menu button. Picture icon will be high- lightedSound Control Adjusting the VolumeUsing Mute Selecting the Color ToneCustomizing the Sound Press the Menu button exitUsing Automatic Sound Settings Sure to select the proper time of day AM or PM Setting the ClockWhen selecting the hours, be You press the Display buttonViewing an External Signal Source Press the VOL + or VOL button to adjust the fine tuning Fine Tuning ChannelsAfter you adjust the fine tuning Star icon*will appearDigital Noise Reduction Press the CH button to select Digital NRWide TV Changing the Screen Size43 TV Press the Aspect button to change the screenUsing the R.surf feature Setting the On/Off Timer Before using the timer, you mustPress the Sleep button on the remote control Setting the Sleep TimerWhen finished, press the VOL + button To deactivate the On time, select Off during this stepExtra sound settings Surround, Auto Volume, Melody, BBE SurroundSelect MTS, then Press Choosing a Multi-Channel Sound MTS SoundtrackSelect Sound, then Select Mono, SAP, orViewing Closed Captions Select Mode, then pressSelect Caption or Text Viewing Picture-in-Picture Activating Picture-in-PictureQuick way to access the signal Selecting a Signal Source Antenna or Cable for PIPSelecting a Signal Source External A/V for PIP Select PIP, then pressSwapping the Contents of the PIP Image and Main Image Changing the Size of the PIP WindowChanging the PIP Channel Simply press the PIP CH button on the remote controlChanging the Location Rotating in PIP mode Scanning the Available ChannelsHighlighted blinking Viewing the DemonstrationPicture icon will be Select DemonstrationCustomizing Your Remote Control Setting Up Your Remote Control to Operate Your VCR or DVDTurn off your VCR or Setting Up Your Remote Control to Operate Your Cable Box Codes VCR CodesCable Box DVD CodesIdentifying Problems Chapter FiveCleaning and Maintaining Your TV Using Your TV in Another CountrySpecifications M O Appendix A.3