Samsung ST43T8PC manual Selecting a Signal Source Antenna or Cable for PIP, Select PIP, then press

Page 53

S P E C I A L F E AT U R E S

Selecting a Signal Source (Antenna or Cable) for PIP

1

Press the Menu button.

Press the CH button to select “PIP”, then press the VOL + button.


					PIP
			PIP		: On
			SOURCE		: TV
			Size		: Double Screen
			Swap
			ANT/CATV		: ANT
			Channel		: ANT 4

2

Press the CH button to select “ANT/CATV.”

If an antenna is connected, the setting is “ANT.”

If a Cable TV system is pro- viding the signal, press the VOL + or VOL - button until the appropriate type of cable system is is displayed (“STD,” “HRC,” or “IRC”).

Press the Menu button to exit.


					PIP
			PIP		: On
			PIP		: On
			SOURCE		: TV
			Size		: Double Screen
			Swap
			ANT/CATV		: ANT
			Channel		: ANT 4

Selecting a Signal Source (External A/V) for PIP

1

PIP

Press the Menu button.

PIP

: On

Press the CH

button to

SOURCE

: TV

Size

: Double Screen

select “PIP”, then press the

Swap

ANT/CATV

: ANT

VOL + button.

Channel

: ANT 4

▼	Quick way to access the signal

source (PIP): Simply press the “Source” button on the remote control.

2

Press the CH button to select “SOURCE”, then press the VOL + or VOL - button to cycle through all of the available signal sources:

“TV”, “Video 1”, “Video 2”, “Video 3”, “S-Video 1”, and “S-Video 2”.

Press the Menu button to exit.


					PIP
			PIP		: On
			PIP		: On
			SOURCE		: TV
			Size		: Double Screen
			Swap
			ANT/CATV		: ANT
			Channel		: ANT 4

▼	If you select “TV”, the PIP image is

the same as the main image.

CHAPTER FOUR: SPECIAL FEATURES 4.11

Image 53

Contents Owner’s Risk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding Safety Operation InstallationYour New TV Troubleshooting Special FeaturesChapter One List of FeaturesFamiliarizing Yourself with The TV Side Panel Jacks Using the Component Shelf´ Video Input jack Audio Input jacksAntenna terminals ¨ Audio Input jacks Rear Panel Jacks Depending on the model´ AUDIO-VIDEO Monitor Output jacks Video Input jacksPower Remote Control´ +100 StillMain¿ S.Mode ˘ R.surf¸ P.Mode ˛ VCR controlsAntennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasAntennas with 75-ohm Round Leads Connecting Cable TVSeparate VHF and UHF Antennas Cable without a Cable BoxCable with a Cable box that Descrambles All Channels Connecting to a Cable Box that Descrambles Some ChannelsThis terminal might be labeled ANT IN, VHF IN, or simply,Install AT I O N Connecting a VCR Connecting a Second VCR to Record from the TV Connecting a CamcorderConnecting to Y, PB, PR Connecting a DVD Player, DTV Set-Top Box 480i, 480pConnecting a DTV Set-Top Box 480p Make sure to match the + Installing Batteries in the Remote ControlInstall two AAA size batteries Replace the cover You can also use the Power button on the front panel Plug & Play FeaturePress the Power button Turning the TV On and OffRefer to Auto program on CH or CH button. refer to Setting the clock on1Press the Menu button Focus by pressing the Perfect Focus button Using the Perfect Focus FeatureYou can also select Perfect Adjusting Manual Convergence If a horizontal red line is visible, use Adjust Red ConvergenceViewing the Display Viewing the Menus and On-Screen DisplaysViewing the Menus Press the VOL + or VOL button to select a or B Selecting a Menu LanguageSelecting the Antenna Input ANT antenna, STD, HRC or IRC Selecting the Video Signal-sourceMemorizing the Channels Adding and Erasing Channels Manual Method Storing Channels in Memory Automatic MethodTV automatically cycles Using the Number Buttons Using the Channel ButtonsUsing the Previous Channel Changing ChannelsTo Store Your Favorite Channels Selecting Your Favorite ChannelsCan be set as Favorite channels To View Your Favorite ChannelsAdding and Erasing Channels Manual Method Labeling the Channels Labeling in the A/V modePress CH or CH to tune to the channel that will be labeled Select Channel, thenPicture Control After adjusting an item,Customizing the Picture Gauge will automatically disappearafter about 4 secondsPress the Menu button. Picture icon will be high- lighted Using Automatic Picture SettingsUsing Mute Adjusting the VolumeSound Control Selecting the Color TonePress the Menu button exit Customizing the SoundUsing Automatic Sound Settings When selecting the hours, be Setting the ClockSure to select the proper time of day AM or PM You press the Display buttonViewing an External Signal Source After you adjust the fine tuning Fine Tuning ChannelsPress the VOL + or VOL button to adjust the fine tuning Star icon*will appearPress the CH button to select Digital NR Digital Noise Reduction43 TV Changing the Screen SizeWide TV Press the Aspect button to change the screenUsing the R.surf feature Before using the timer, you must Setting the On/Off TimerWhen finished, press the VOL + button Setting the Sleep TimerPress the Sleep button on the remote control To deactivate the On time, select Off during this stepSurround Extra sound settings Surround, Auto Volume, Melody, BBESelect Sound, then Choosing a Multi-Channel Sound MTS SoundtrackSelect MTS, then Press Select Mono, SAP, orSelect Caption or Text Viewing Closed CaptionsSelect Mode, then press Activating Picture-in-Picture Viewing Picture-in-PictureSelecting a Signal Source External A/V for PIP Selecting a Signal Source Antenna or Cable for PIPQuick way to access the signal Select PIP, then pressChanging the Size of the PIP Window Swapping the Contents of the PIP Image and Main ImageChanging the Location Rotating in PIP mode Simply press the PIP CH button on the remote controlChanging the PIP Channel Scanning the Available ChannelsPicture icon will be Viewing the DemonstrationHighlighted blinking Select DemonstrationTurn off your VCR or Customizing Your Remote ControlSetting Up Your Remote Control to Operate Your VCR or DVD Setting Up Your Remote Control to Operate Your Cable Box Cable Box VCR CodesCodes DVD CodesChapter Five Identifying ProblemsSpecifications Cleaning and Maintaining Your TVUsing Your TV in Another Country M O Appendix A.3