Samsung ST43L2HD Your New Wide TV, Replacing the Lamp, Remove the Lamp cover Use a screwdriver to

Page 6

Your New Wide TV

Replacing the Lamp

•A Projection TV lamp is a consumable item, and should be replaced from time to time for best projec- tor operation. If the screen image becomes dark, or timer, lamp and Temp LEDs flicker off at the same time, you may have to replace the lamp.

•When changing the lamp, you should first verify the type/model, and then use only the correct lamp replacement. The code for lamp regulation and usage is marked on the label. If you remove the lamp, you can identify this replacement code. You should only replace the lamp with the one of the same reg- ulation code.

•If you wish to buy a new lamp, please phone your Service Center or a nearby TV dealer, and tell them the model of your projection unit.

•You can identify the lamp type on the left side of TV and the lamp cover.

•The TV will be damaged if you use a lamp that is different from the original supplied by the manufac- turer.

•Please don't remove the lamp except when replacing with a new one.

•Please turn off TV power before changing a lamp and then unplug after waiting 1 minute.

•The cooling fan will help cool the lamp so you can safely remove it. The surface of the Lamp is very hot. Please wait for 30 minutes after turning off your projection TV to handle the lamp.

•Please keep the old lamp away from flammable articles and children. Dispose of properly.

•Don't allow dirt or dust to accumulate inside the lamp cover or on the Lamp.

•A dirty cover or lamp can catch fire, explode and cause electric shock.

•Please don't touch the front glass of a new lamp or the glass of the lamp container.

•If a new lamp is improperly handled, the quality of the screen image can be affected and the expected life span of the lamp can be reduced.

•Be sure to tighten the lamp cover on the TV after changing the lamp. Note that the TV will not function if the lamp cover is not securely attached. Please tighten the holding screw on the lamp cover after it has been attached to the TV.

Use a screwdriver to

1 remove the screw as shown in the picture.

2 Remove the Lamp cover.

Use a screwdriver to

3 remove the screws securing the Lamp. There are 2 screws: one on the left and one on the right. When the screws have been completely unfastened, they will still be connected to the body of the Lamp.

Separate the Lamp from

4 the engine by holding the handle and pulling it out.

To reinstall the Lamp, fol-

5 low these steps in reverse order.

NOTE

• Be sure the replacement Lamp is the same model.

10

11

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Dlptv Dlptv Safety Instructions Important Safety InformationThank You for Choosing Samsung FCC Information Table of Contents M S U N G Your New Wide TV Replacing the LampRemove the Lamp cover Use a screwdriver to Checking Parts List of FeaturesSide Panel Buttons Side Panel JacksRear Panel Jacks Front Panel LED IndicatorsIndicator Light Key Light is On Light is BlinkingInstall two AAA size batteries Remote ControlInstalling Batteries in the Remote Control Slide the back cover all the way outM S U N G Antennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasN n e c t i o n s Separate VHF and UHF AntennasConnecting a Cable Converter Box and a VCR Connecting Cable TV and VCRConnecting a Cable Converter Box Cable without a Cable BoxConnecting to Y,Pb,Pr Connecting a CamcorderConnecting a DVD Player Connecting to audio and video jacksConnecting to DVI Digital Visual Interface Connecting a DTV Set Top BoxConnecting to R,G,B Connect a set of audioM S U N G Viewing the Menus and Displays E r a t i o nTurning the TV On and Off Selecting the Menu LanguageStoring Channels in Memory Automatically Channel MemorySelecting the Broadcast Source Adding and Erasing ChannelsChanging Channels Selecting Your Favorite ChannelsSetting The On/Off Melody Labeling the ChannelsZ, blank,0,1,...9 Move the joystick to the right Using Automatic Standard Picture Settings Picture ControlCustomizing the Picture Using AutomaticStandard Sound Settings Adjusting the VolumeUsing the Mute Button Sound ControlSetting the Clock Setting the TimersSetting the On/Off Timer Selecting the Signal Source Viewing an External Signal SourceSetting the Sleep Timer Remote Control VCR/DVD ButtonsSpecial Features Setting Up the Remote to Operate Your VCR Special FeaturesSetting Up Your Remote Control Setting Up the Remote to Operate Your Cable BoxRemote Control Codes Setting Up the Remote to Operate Your DVDVCR Codes Cable Box Codes DVD Codes Selecting the Color Tone Fine Tuning ChannelsSetting the Film Mode 480i onlyOn Switches on the DNIe mode DNIeTM Digital Natural Image engineDigital Noise Reduction Setting the Blue Screen Mode Changing the Screen SizeMTS Settings Choosing a Soundtrack Special Audio OptionsDolby Virtual BBEAuto Volume Viewing Closed Caption InformationClosed Captions Selecting an External Signal Viewing Picture-in-PictureSelecting a PIP Screen Selecting a Signal Source Antenna or Cable for PIP Swapping the Contents of the PIP and Main imageChanging the Size of the PIP image Changing the Picture-in-Picture ChannelSelecting the Sound Source Using the V-ChipSetting Up Your Personal ID Number PIN Changing the Location of the PIP imageHow to Enable/Disable the V-Chip How to Set up Restrictions Using the TV guidelinesJoystick to enter Parental guidance suggestedNot rated PC Display How to Set up Your PC Software Windows only Using Your TV as a Computer PC DisplayHow to connect Your PC to the TV D i s p l a yHow to Set up Your TV as a PC display Display ModesPicture Quality Adjustment Frequency AdjustmentFine tuning Wide TV Changing the Screen Size PC modeAspect Supported settings Wide PCAppendix Using the TV in Another Country TroubleshootingCare and Maintenance SpecificationsM o
Top Page Image Contents