Samsung ST43L2HD Connecting a Camcorder, Connecting a DVD Player, Connecting to Y,Pb,Pr

Page 13

C o n n e c t i o n s

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV.

You can use your camcorder to view tapes without using a VCR.

Locate the A/V output jacks

1 on the camcorder. They are usually found on the side or back of the camcorder.

Connect an audio cable

2 between the AUDIO OUT- PUT jack on the camcorder and the AUDIO terminals on the side of the TV.

If your camcorder is stereo, you must connect two sepa- rate cables.

(The audio cables are usual- ly included with the cam- corder.)

Connect a video cable

3 between the VIDEO OUT- PUT jack on the camcorder and the VIDEO terminal on the side of the TV. (A video cable is usually included with the camcorder.) To watch a tape, follow your camera’s instructions and the section on “Viewing an External Signal Source” in this manual.

Connecting a DVD Player

The rear panel jacks on your TV make it easy to connect a DVD player to your TV.

Connecting to Y,Pb,Pr

Connect a set of audio

1 cables between the Component1AUDIO IN jacks on the TV and the AUDIO OUT jacks on the DVD player.

To enable Component video

2 viewing, connect video cables between the Component1 (Y, Pb and Pr) jacks on the TV and Y, Pb and Pr (or Y, Cb, Cr) output jacks on the DVD player.

Note: For an explanation of Component video, see your DVD player's owner's man- ual.

Connecting to audio and video jacks

Connect a set of audio

1 cables between the AUDIO IN jacks on the TV and the AUDIO OUT jacks on the DVD player.

Connect video cables

2 between the VIDEO OUT jack on the DVD player and the VIDEO IN jack on the TV.

24

25

Image 13

Contents Dlptv Dlptv Important Safety Information Safety InstructionsThank You for Choosing Samsung FCC Information Table of Contents M S U N G Replacing the Lamp Your New Wide TVRemove the Lamp cover Use a screwdriver to Side Panel Buttons List of FeaturesChecking Parts Side Panel JacksIndicator Light Key Front Panel LED IndicatorsRear Panel Jacks Light is On Light is BlinkingInstalling Batteries in the Remote Control Remote ControlInstall two AAA size batteries Slide the back cover all the way outM S U N G N n e c t i o n s Connecting VHF and UHF AntennasAntennas with 300-ohm Flat Twin Leads Separate VHF and UHF AntennasConnecting a Cable Converter Box Connecting Cable TV and VCRConnecting a Cable Converter Box and a VCR Cable without a Cable BoxConnecting a DVD Player Connecting a CamcorderConnecting to Y,Pb,Pr Connecting to audio and video jacksConnecting to R,G,B Connecting a DTV Set Top BoxConnecting to DVI Digital Visual Interface Connect a set of audioM S U N G Turning the TV On and Off E r a t i o nViewing the Menus and Displays Selecting the Menu LanguageSelecting the Broadcast Source Channel MemoryStoring Channels in Memory Automatically Adding and Erasing ChannelsSelecting Your Favorite Channels Changing ChannelsLabeling the Channels Setting The On/Off MelodyZ, blank,0,1,...9 Move the joystick to the right Picture Control Using Automatic Standard Picture SettingsCustomizing the Picture Using the Mute Button Adjusting the VolumeUsing AutomaticStandard Sound Settings Sound ControlSetting the Timers Setting the ClockSetting the On/Off Timer Setting the Sleep Timer Viewing an External Signal SourceSelecting the Signal Source Remote Control VCR/DVD ButtonsSpecial Features Setting Up Your Remote Control Special FeaturesSetting Up the Remote to Operate Your VCR Setting Up the Remote to Operate Your Cable BoxSetting Up the Remote to Operate Your DVD Remote Control CodesVCR Codes Cable Box Codes DVD Codes Setting the Film Mode Fine Tuning ChannelsSelecting the Color Tone 480i onlyDNIeTM Digital Natural Image engine On Switches on the DNIe modeDigital Noise Reduction Changing the Screen Size Setting the Blue Screen ModeSpecial Audio Options MTS Settings Choosing a SoundtrackBBE Dolby VirtualViewing Closed Caption Information Auto VolumeClosed Captions Viewing Picture-in-Picture Selecting an External SignalSelecting a PIP Screen Swapping the Contents of the PIP and Main image Selecting a Signal Source Antenna or Cable for PIPChanging the Picture-in-Picture Channel Changing the Size of the PIP imageSetting Up Your Personal ID Number PIN Using the V-ChipSelecting the Sound Source Changing the Location of the PIP imageHow to Set up Restrictions Using the TV guidelines How to Enable/Disable the V-ChipParental guidance suggested Joystick to enterNot rated PC Display How to connect Your PC to the TV Using Your TV as a Computer PC DisplayHow to Set up Your PC Software Windows only D i s p l a yDisplay Modes How to Set up Your TV as a PC displayFrequency Adjustment Picture Quality AdjustmentFine tuning Aspect Supported settings Changing the Screen Size PC modeWide TV Wide PCAppendix Care and Maintenance TroubleshootingUsing the TV in Another Country SpecificationsM o