Onkyo PR-SC885 Connecting an RI Dock, Connecting the Power Cords of Other Components

Connecting Your Components—Continued

Connecting an RI Dock

■ If Your iPod Supports Video:	■ If Your iPod Doesn’t Support Video:
Connect your RI Dock’s audio output jacks to the	Connect your RI Dock’s audio output jacks to the
AV controller’s GAME/TV IN L/R jacks, and con-	AV controller’s GAME/TV IN L/R jacks.
nect its video output jack to the AV controller’s	(Onkyo DS-A2 hookup shown below.)
GAME/TV IN V jack.
(Onkyo DS-A2 hookup shown below.)
	IN

L

HDMI

ASSIGNABLE

RS232

IN 4

IN 3

IN 2

IN 1

XM

COMPONENT VIDEO ASSIGNABLE

MONITOR OUT 2

SIRIUS

R

/ZONE 2 OUT

GAME/TV

IN 3

IN 2

IN 1(DVD)

MONITOR

OUT 1

HDMI

Y

ASSIGNABLE

V

RS232

IN 4

IN 3

IN 2

I

AUX 1

GAME/TV

CBL/SAT

GAME/TV

CONTROL

V

XM

CB/PB

REMOTE

COMPONENT VIDEO ASSIGNABLE

MONITOR OUT 2

SIRIUS

DIGITAL ASSIGNABLE

/ZONE 2 OUT

COAXIAL

IN 3

IN 2

IN 1(DVD)

MONITOR

IN 1

CR/PR

OUT 1

(DVD)

Y

S

AUX 1

GAME/TV

CBL/SA

IN

IN

OUT

IN

IN

IN

IN

U

IN 2

(VCR/DVR)

V

L

L

REMOTE CB/PB

CONTROL

IN

DIGITAL ASSIGNABLE

IN 3

(CBL/SAT)

R

R

IN 1

COAXIAL

(DVD)

CR/PR

OPTICAL

L

S

IN 1

PHONO

CD

TAPE

AUX 1

GAME/TV

CBL/SAT

IN

IN

IN

IN

IN

OUT

IN

(GAME/TV)

IN 2

(VCR/DVR)

GND

BALANCE L

SURR BACK R

SURR R

L

L

BALANCE R

MONO

Bi-AMP

IN 2

	IN 3							(CD)	2	1
R		(CBL/SAT)	R	R						3
		OPTICAL						OUT	HOT	GND
	IN 1			PHONO	CD	TAPE	AUX 1 GAME/TV	CBL/SA
									COLD
		(GAME/TV)	GND			BALANCE L	SURR BACK R		INPUT
GAME/TV				BALANCE R		MONO	Bi-AMP	SURR R
	IN 2
		(CD)	2	1
			3
	OUT		HOT	GND
			COLD
			INPUT

■If you have an Onkyo DS-A1 RI Dock

•Connect its video output jack to the AV controller’s GAME/TV IN S jack.

•Enter the appropriate remote control code before using the AV controller’s remote controller for the first time (see page 116).

Notes:

•Connect the RI Dock to the AV controller with an cable (see page 42).

•Set the RI Dock’s RI MODE switch to HDD or HDD/DOCK.

•Set the AV controller’s Input Display to DOCK (see page 49).

•See the RI Dock’s instruction manual for more information.

Connecting the Power Cords of Other Components

The AV controller has AC outlets on its rear panel that can be used to connect the power cords of other components that you intend to use with the AV controller. These components can then be left turned on so that they turn on and off as and when the AV controller is set to On or Standby.

Caution:

•Make sure that the total capacity of the components that you connect to the AC OUTLETS does not exceed the stated capacity (e.g., TOTAL 120 W).

AC INLET
AC OUTLET
AC 120V	60Hz
SWITCHED
120W 1A MAX.

Note:

•When the HDMI Control setting is set to Enable (page 107), the AC outlets are on all the time regardless of whether the AV controller is set to On or Standby, or Ready mode in this case, so any components connected to them cannot be turned on or off automatically.

•Onkyo components connected via should be connected directly to a wall outlet, controller.

AC OUTLET

AC 120V60Hz

SWITCHED

120W 1A MAX.

not an AC OUTLET on the AV

41