Samsung HLN5065W1, HLN4365W1, HLN617W1, HLN437W1 HLN507W1 Your New Wide TV, Replacing the Lamp

Page 6

Your New Wide TV

Replacing the Lamp

•Why do I need to replace the lamp?

The lamp used in a projection TV has a limited lifespan. For the best screen quality it needs to be replaced periodically.

After replacing the lamp, the screen quality will be bright and clear as new.

•When do I need to replace it?

It should be replaced when the screen becomes darker, less clear or when all three LEDs on the front (Timer, Lamp, & Temp.) are flashing.

•Check before lamp replacement

1.The lamp must be the same code number and type.

2.The lamp type is indicated on the right side of the TV. It is also indicated on the lamp case.

3.After checking the code number for the lamp, give the code number to the store where you purchased the TV or to a Samsung Service center.

… HLN437W1/HLN507W1	… HLN467W1/HLN567W1
HLN617W1/HLN4365W1
HLN5065W1

•Caution

1.Replace with the correct code numbered lamp to avoid damage to the TV.

2.Turn the power off and wait for 30 minutes before replacing the lamp as it will be hot.

3.Do not touch the glass part of the lamp with your bare hands nor insert any foreign object inside the cover as it may cause poor screen quality, electric shock or fire.

4.Do not place the old lamp near flammable objects or within the reach of children.

10

• For replacement, you will need a 5.91 Inches-long Phillips screwdriver and a pair of gloves.

Unplug TV, then use a

1 screwdriver to remove the screw as shown in the picture. (HLN467W1/HLN567W1: Remove the rubber cap and unscrew the screw.)

Remove the Lamp cover.

2 (HLN467W1/HLN567W1: Exert a bit of force to the right and pull for easy opening.)

Use a screwdriver to

3 remove the screws securing the Lamp. There are 2 screws: one on the left and one on the right. When the screws have been completely unfastened, they will still be connected to the body of the Lamp.

Separate the Lamp from

4 the engine by holding the handle and pulling it out.

To reinstall the Lamp,
5 follow these steps in	… HLN437W1/HLN507W1 … HLN467W1/HLN567W1
reverse order.	HLN617W1/HLN4365W1
	HLN5065W1

NOTES

• Be sure the replacement Lamp is the same type.

• After replacing the lamp, align the lamp cover with the groove and secure the screw.

• The TV will not turn on if the lamp cover is not correctly closed (as this will activate the protective circuit).

11

Image 6

Contents Dlptv Dlptv Safety Instructions Important Safety InformationThank You for Choosing Samsung FCC Information User InstructionsTable of Contents M S U N G Your New Wide TV Replacing the LampSide Panel Buttons List of FeaturesChecking Parts Side Panel JacksFront Panel LED Indicators Rear Panel JacksRemote Control Installing Batteries in the Remote ControlM S U N G Antennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasN n e c t i o n s Separate VHF and UHF AntennasConnecting a Cable Converter Box and a VCR Connecting Cable TV and VCRConnecting a Cable Converter Box Cable without a Cable BoxConnecting a Camcorder Connecting a DVD PlayerConnecting to Y,PB,PR Connecting to DVI Digital Visual Interface Connecting to R,G,BOperation Selecting the Menu Language E r a t i o nTurning the TV On and Off Viewing the Menus and DisplaysChannel Memory Selecting the Broadcast SourceAdding and Erasing Channels Changing Channels Selecting Your Favorite ChannelsScanning Channels Labeling the Channels Using Automatic Standard Picture Settings Picture ControlCustomizing the Picture Using AutomaticStandard Sound Settings Adjusting the VolumeUsing the Mute Button Sound ControlSetting the Clock Setting the TimersSetting the On/Off Timer Setting the Sleep Timer Absent Power OffViewing an External Signal Source Selecting the Signal SourceAssigning Names to External Input Mode Special Features Remote Control VCR/DVD ButtonsSetting Up the Remote to Operate Your VCR Special FeaturesSetting Up Your Remote Control Setting Up the Remote to Operate Your Cable BoxVCR Codes Remote Control CodesSetting Up the Remote to Operate Your DVD Cable Box CodesFine Tuning Channels Setting the Film Mode Selecting the Color Tone DNIeTM Digital Natural Image engineSetting the Blue Screen Mode Digital Noise ReductionChanging the Screen Size Special Audio OptionsVirtual Dolby BBESetting The On/Off Melody Auto VolumeViewing Closed Caption Information Viewing Picture-in-PictureSelecting a PIP Screen Closed Captions Selecting an External Signal Selecting a Signal Source Antenna or Cable for PIPSwapping the Contents of the PIP and Main image Changing the Size of the PIP imageChanging the Location of the PIP Image Changing the Picture-in-Picture ChannelUsing the V-Chip How to Change Your PasswordSelecting the Sound Source How to Enable/Disable the Rating Controls How to Set up Restrictions Using the TV Parental GuidelinesYou can independently lock Important Notes About Parental Locks TV FCC Age-Based RatingsHow to Set up Your PC Software Windows only Using Your TV as a Computer PC DisplayHow to connect Your PC to the TV PC DisplayHow to Set up Your TV as a PC display Display ModesPicture Quality Adjustment Frequency AdjustmentFine tuning Select PC Setup, then press the Enter button Wide TV Changing the Screen Size PC modeAspect Supported settings Wide PCAppendix Using the TV in Another Country TroubleshootingCare and Maintenance Specifications