Hitachi 65G500 Using the Remote to Control CABLE/SATELLITE BOX Functions, Cable CBL/SAT button

Page 29

USING THE REMOTE TO CONTROL

CABLE/SATELLITE BOX FUNCTIONS

Operating the precoded function for your cable/satellite box.

This remote is designed to operate different types of cable/satellite boxes. You must first program the remote to match the remote sys- tem of your cable/satellite box (refer to page 31).

1.Turn ON your cable/satellite box.

2.Aim the remote control at the front of your cable/satellite box.

3.Press and release the cable/satellite (CBL/SAT) button to switch to cable/satellite pre-coded mode.

4.Hold down the CBL/SAT button on the remote and enter the two digit preset code that matches your cable/satellite box as shown on page 31.

5.Aim the remote at the cable/satellite box and press the POWER button. The remote will turn off your cable/satellite box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable/satellite box. If the box does not turn off, try a different two digit preset code.

6.The remote will now control your cable/satellite box.

NOTES:

1.If your cable/satellite box cannot be operated after performing the above procedures, your cable/satellite box code has not been precoded into the remote.

2.In the unlikely event that your cable/satellite box cannot be operated after performing the above procedures, please consult your cable/satellite box operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

aCABLE (CBL/SAT) button

This button allows the remote to control your cable/satellite box by setting it to CABLE/SATELLITE mode.

bPRECODED CABLE/SATELLITE BOX buttons

These buttons transmit the chosen precoded cable/satellite codes.

cEXCLUSIVE TV buttons

These buttons are for operating the TV.

a

c

	POWER
TV	CBL/SAT DVD/VCR
PIP	SWAP PIP MODE
PIP	FREEZE

PIP CH

VIDEOMENU

SELECT

MUTE	LAST CH
	EXIT

VOL CH

b

1 2 3

4 5 6

7 8 9

ANT 0 INFO

VID1	VID2	VID3	VID4
REC		ASPECT VIRTUAL HD
	VID5

THE REMOTE CONTROL

MY CABLE/SATELLITE

BOX CODE IS:

NOTE: Refer to instruction manual of the Cable/Satellite Box for operation of the buttons exclusively for the Cable/Satellite Box.

29

Image 29

Contents Useful Information Index Important Safety Instructions First Time USE Remote ControlON-SCREEN Display Safety Points YOU should Know about Your Hitachi Television Important Safety InstructionsPublic Viewing of Copyrighted Material Prevention of Screen BurnPart Name Illustration Remote Control AccessoriesAntenna HOW to SET UP Your NEW Hitachi Projection TVLocation ViewingAntenna Connections to Rear Jack Panel HOOK-UP Cables and ConnectorsFront Panel Controls Front Panel Jacks and Connectors Rear Panel Jacks DVI-HDTV Input Input Component Y-PBPRInputsRear Panel Connections Typical FULL-FEATURE SetupTips on Rear Panel Connections Rear Panel of Television Connecting External Audio DevicesBefore Operating External Video Source Connecting External Video SourcesConnecting a Monaural Audio Source to INPUT1~INPUT5 Connecting a Stereo Source to INPUT1~INPUT5 Connecting AN S-VIDEO Source to Input 3, 4 VHS DVD Player Connecting a Component Source to Input 1 or 2 Y-PBPRTV or VCR/DVD Buttons ControlPICTURE-IN-PICTURE buttons HOW to USE the Remote to Control Your TVVideo button SELECT, MENU, Cursor buttonsChannel selector buttons VOLUME, Mute buttonAntenna button VID1 ~ VID5Standard Aspect buttonInfo button Virtual HD buttonExit button Last Channel Last CH buttonPIP button POP Mode PICTURE-IN-PICTUREPICTURE-IN-PICTURE PIP Surf Mode PICTURE-IN-PICTURE Split Mode PICTURE-IN-PICTUREPIP Mode button Swap buttonFreeze button with PIP OFF Freeze button With PIP onPOP SUB Freeze with PIP OFF Split FREEZEwith PIP OFFOperating the precoded function for your VCR Using the Remote to Control VCR FunctionsDVD/VCR Button Precoded VCR ButtonsPrecoded CABLE/SATELLITE BOX buttons Using the Remote to Control CABLE/SATELLITE BOX FunctionsCable CBL/SAT button Precoded DVD Buttons Using the Remote to Control DVD FunctionsOperating the precoded function for your DVD player Cable Brand Code CABLE, SATELLITE, VCR and DVD Codes for Remote ControlON-SCREEN Display OSD Press Cursor F or E to access Favorite Channels menuVideo Video Picture ModeContrast Brightness Color Tint Sharpness Vertical Position Magic Focus Auto Digital Convergence AdjustmentTo Move Adjustment Point Manual Convergence Adjustment ModeTo Change the Color of Adjustment Point To Adjust the ConvergenceAdvanced SettingsTreble Bass Balance AudioTechnology Sound EnhancementAdvanced Settings Scan Channel ManagerChannel ID Locks LocksParental guidance suggested Movie RatingsParents strongly cautioned. Some No one 17 and under admittedTV Ratings Eng Canadian Ratings English ChartCanadian Ratings Frn Canadian Ratings French Chart+ General Not recommended for young Programming is not suitable for childrenMenu Preference SetupSet The Clock Set Menu BackgroundAIR Catv Channel Reception BandAuto Channel Scan Set The Inputs Video2 Auto Link Video 2 Auto LinkPlease Set Clock First Set Event TimerClosed Caption Caption ModeChannel About Your TVDo not Care of Your Hitachi Television Your Remote ControlReception Problems Useful Info SymptomsOutputs InputsHome Electronics Division Dial Toll FreeDigital Media Division Index QR54415