Hitachi 51F710G, 57F710G Remote Control for Cable Box Functions, Cable Brand Codes

Page 26

The Remote Control for Cable Box Functions

The Remote Control

OPERATING THE PRECODED

FUNCTION FOR YOUR CABLE BOX.

This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of your cable box (refer below for pre-codes).

1.Turn ON your cable box.

2.Aim the remote control at the front of your cable box.

3.To switch to Cable (CBL) pre-coded mode, press and release the CABLE (CBL) button.

4.Hold down the CBL button on the remote and enter the two digit preset code that matches your cable box, as shown below. Release the CBL button.

5.Aim the remote at the cable box and press the POWER button. The remote will turn off your cable box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable box. If the cable box does not turn off, try a different two digit preset code.

6.The remote will now control your Cable box.

NOTE: 1. If your cable box cannot be operated after performing the above procedures, your cable box code has not been precoded into the remote.

2.In the unlikely event that your cable box cannot be operated after performing the above procedures, please consult your cable box operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

CABLE (CBL) button

This button allows the remote to control your cable box by setting it to CABLE mode.

PRECODED CABLE BOX buttons

These buttons transmit the chosen precoded cable codes.

EXCLUSIVE TV buttons

These buttons are for operating the TV.

CABLE BRAND	CODES
HAMLIN	22, 23, 24, 25
JERROLD	00, 01, 02, 03, 04, 05, 06, 07
OAK	26, 27, 28
PANASONIC	18, 19, 20
PIONEER	13, 14
SCIENTIFIC ATLANTA	08, 09, 10
TOCOM	15, 16
ZENITH	11, 12

MY CABLE BOX CODE IS: _______________________

NOTE: Refer to instruction manual of the Cable Box for operation of the buttons exclusively for the Cable Box.

26

Image 26

Contents Useful Information Important Safety Instructions First Time USE Remote ControlON-SCREEN Display Read Before Operating Equipment Important Safety InstructionsSafety Points YOU should Know about Your Hitachi Television For More INFORMATION, Call 1-800-HITACHI Accessories Remote Control Battery Installation and ReplacementLocation How to set up your new Hitachi Projection TelevisionAntenna ViewingHook-up Cables and Connectors Antenna Connections to Rear Jack PanelQuick Reference Remote Control Buttons and Functions Front Input Jacks Input Front Panel ControlsMagic Focus Front Panel Jacks and Connections Rear Panel Connections TV AS Center Inputs CableCARD SlotTips on Rear Panel Connections VIDEO,Y-PBPRand HdmiConnecting External Audio Sources Speaker placementConnecting External Video Sources Before Operating External Video SourceConnecting AN S-VIDEO and Stereo Source to Input 1, 2 First timeHdmi or DVI Capability to Input InputConnecting a Component and AN Audio Remote Control Mode buttons How to Use the Remote to Control Your TVPower button Pause buttonExpanded StandardZOOM1/ZOOM2 Menu button Inputs buttonPICTURE-IN-PICTURE button Exit buttonChannel CH Down WhiteSub-picture Cable or AIR POP Mode Picture-in-PicturePicture-in-Picture PIP PIP buttonSurf PIPPOP Strobe Freeze Main FreezeSplit Freeze Cable Brand Codes Remote Control for Cable Box FunctionsOperating the Precoded Function for Your Cable BOX SET TOP BOX Brand Codes Remote Control for Set-Top Box/Satelite Receiver FunctionsSatellite Brand Codes MY Satellite ReceiverDVD Brand Codes Remote Control for DVD FunctionsOperating the Precoded Function for Your DVD Player VCR Brand Codes Remote Control for VCR FunctionsOperating the Precoded Function for Your VCR On-Screen Display DRC SRSBBE Video Aspect Mode Virtual HD Reset Video SettingsBlack Side Panel BBE AudioSRS ST/SA StereoMono PCM LanguageDigital Output DRCChannel Manager Signal MeterSignal Meter Cable or AIR Start or Reset optionAuto Channel Scan Channel ListChange Access Code LocksNot Rated Movie RatingsMotion Picture Ratings Table TV Ratings TV Parental Guide Ratings TableCanadian Ratings Eng Canadian Ratings English TableCanadian Ratings French Chart AM or PM, MONTH, DAY, and Year TimersSet The Clock DAY/NIGHT Picture Mode automatically Set Sleep TimerSet Day/Night Timer DAY Mode on and to set it’s TimerMonth Setup Magic Focus Tune Up Auto Digital Convergence AdjustmentMenu Focus Tune UP, Manual Adjustment Mode To Move Adjustment PointSetup SET the Menu Background Shaded or SolidInput Monitor Digital CaptionsSet Monitor Out TV Tuner OutInsert MMC Card UpgradesUpgrade NOW Quick Start UpImportant Points Disassembly/Assembly InstructionsDisassembly Procedure Step Left side Right sideDisassembly/Assembly Instructions Assembly Procedure Step InformationSwitch ON/OFF Equipment Care and TroubleshootingTroubleshooting Switch onceReception Problems Dimensions Features and SpecificationsFeaturesinputs OutputsDigital Media Division HitachiHome Electronics Division Canada 1-800-HITACHIEnd User Licence Agreement for Hitachi DTV Software END User License Agreement for Hitachi DTV SoftwareCableCARD Information and press Appendix Additional CableCARD InformationIndex Select buttonPage Page Page Page Page Page Page QR64233