Hitachi 50VS810 Using Your Remote To Control Additional Audio Equipment, Precoded Audio Buttons

Page 37

USING YOUR REMOTE

TO CONTROL ADDITIONAL AUDIO EQUIPMENT

Operating the precoded function for your Audio component.

This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component (refer to pages 39-40 for pre-codes).

1.Turn ON your Audio component you wish to control with the Remote.

2.Aim the remote control at the front of your Audio component.

3.To switch to Audio (AMP) component pre-coded mode, use the SOURCE ACCESS buttons (F , E) on the remote control to posi- tion the LED light to the corresponding selection.

4.Hold down the ENT button on the remote and enter the four digit preset code that matches your Audio component, as shown on pages 39-40. Release the ENT button. The indicator light will flash 3 times if the code was accepted.

5.Aim the remote at the Audio component and press the POWER button. The remote will turn off your Audio component when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio component does not turn off, try a different four digit preset code.

6.The remote will now control your Audio component.

7.Repeat steps 1 - 6 if you wish to program the remote to control another Audio component.

THE

NOTES:

1.If your Audio component cannot be operated after performing the above procedures, your Audio component’s code has not been precoded into the remote.

2.In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio equipment operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4.CD precode library is included in the AMP mode. Default device for this mode is Hitachi Audio/Video Receiver (AVR/AMP).

5.INPUT, GUIDE, Channel (up/down), Volume (up/down) and REC button are not for CD devices.

aPRECODED AUDIO Buttons

These buttons transmit the chosen precoded Audio component codes.

bEXCLUSIVE TV Buttons

These buttons are for operating the TV.

a

b

GUIDE

b

C.C.

a

a

a

a

REMOTE CONTROL

MY AUDIO EQUIPMENT CODE IS:

CD

AMP/RCVR

NOTES: 1. The REC (Record) button only applies to some precoded amplifier/receiver codes.

2.Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment.

37

Image 37
Contents Operating Guide for 50VS810 Refer Servicing to Qualified Service Personnel Important Safety InstructionsPublic Viewing of Copyrighted Material Read before operating equipmentFirst Time USE AccessoriesHOW to SET UP Your NEW Hitachi LCD Rear PTV Antenna Connections to Rear Jack Panel HOOK-UP Cables and ConnectorsPhoto Input Side Panel ControlsTemp indicator Power lightSide Panel Jacks and Connectors Rear Panel Jacks Hdmi 2 Input 2 Extra Hdmi input Upgrade CardOptical Out Digital Audio RS232C InputCableCARD CableCARD SlotRear Panel Connections Typical FULL-FEATURE SetupTips on Rear Panel Connections Rear Panel of Television Connecting External Audio DevicesConnecting a Monaural Audio Source to INPUT1~INPUT5 Connecting External Video DevicesBefore Operating External Video Source CableCARD Connecting a Stereo Source to INPUT1~INPUT5VCR Connecting AN S-VIDEO Source to Input 3, 4HDMI-HDMI Connecting a Component Source to Input 1 or 2 Y-PBPR Remote Control Mode Indicator HOW to USE the Remote to Control Your LCD Rear PTVSource Access F , E buttons Source Access ENT buttonStandard Aspect buttonPICTURE-IN-PICTURE button DAY/NIGHT buttonMenu button Guide buttonPhoto Input Ant B Ant a Inputs buttonPhoto Input JumpRotate SlideshowInfo button When a S-VIDEOVideo Channel CH WHEEL/CHANNEL Selector buttons Volume VOL WHEEL, Mute buttonDash button Last Channel LC buttonPICTURE-IN-PICTURE PIP POP Mode PICTURE-IN-PICTUREPIP button Split Mode PICTURE-IN-PICTURE PIP Mode PICTURE-IN-PICTURESurf Mode PICTURE-IN-PICTURE NtscSplit Freeze Main FreezeStrobe Freeze Operating the precoded function for your cable box Using the Remote to Control Cable BOX FunctionsPrecoded Cable BOX buttons Exclusive TV buttonsPRE-CODED SET-TOP-BOX/SATELLITE Receiver buttons Operating the precoded function for your DVD player Using the Remote to Control DVD FunctionsPrecoded DVD Buttons Precoded VCR/PVR Buttons Using Your Remote To Control VCR/PVR FunctionsOperating the precoded function for your Audio component Using Your Remote To Control Additional Audio EquipmentPrecoded Audio Buttons Control Input AccessDVD Brand Receiver Brand Amplifier Code ControlON-SCREEN Display OSD Video Audio Aspect Channel Video Picture ModeVideo Color Management Reset Video SettingsColor Decoding Noise Reduction Auto Movie ModeAuto Color Treble Bass Balance AudioTechnology Audio Source Internal Speakers Auto Noise Cancel Perfect Volume LoudnessAudio Language Digital OutputAuto Aspect AspectVertical Position Set The Antenna Channel ManagerAuto Channel Scan Channel List Signal MeterLocks LocksMovie Ratings TV Ratings Canadian Ratings Eng Canadian Ratings English ChartCanadian Ratings Frn Set The Clock TimersSet Day/Night Timer Set Sleep TimerPlease Set Clock First Set Event TimerSet Auto Power Off Menu Preference SetupScreen Saver Set Menu BackgroundOption Screen WipeSet Black Side Set The InputsPanel Set Closed Caption Caption ModeChannel CableCARD Info Set Monitor OutSet AV Control Quick Start Up UpgradesLamp Type Lamp ReplacementLamp Replacement Handle Remove Screws Lamp Unit 120V Do not Care of Your Hitachi Television Your Remote ControlIgnition Noise Reception ProblemsUseful Info SymptomsInputs Dimensions 50VS810 60VS810Outputs Home Electronics Division Dial Toll FreeDigital Media Division DVI Input IndexEND User License Agreement for Hitachi DTV Software END User License Agreement for Hitachi DTV Software Page Page QR62061