Hitachi C50-FD7000, C43-FD7000 Addenda, Guide to simple problem solving, Accessories

Page 54

ADDENDA

A guide to simple problem solving

Before calling up the service personnel, please check the following chart for a possible cause to the problem you are encountering.

Symptom

Possible causes

No picture,no sound,power/standby indicator is OFF.

The power cord is not plugged in.

No picture,no sound,power/standby indicator is ON.

The TV is in standby mode.

No sound

The volume control is set to minimum.

 

The Speaker option in Setup menu is set to Off.

 

 

Twist image and poor sound

The antenna signal is too weak or too strong.

 

The TV is not tuned correctly.

Poor brightness, color or tint

The contrast, brightness, color or tint may be misadjusted.

Snowy picture

Interference from motorcycles, high-tension line, electric hair drier,

 

personal computer or radio station.

Ghosts

Check the direction, height or position of the antenna.

No color

The antenna signal is too weak.

 

Color System or Sound System is not set properly.

Remote controller does not work.

The batteries in the remote controller may be exhausted.

 

The batteries may be improperly installed.

 

There is obstruction between the remote controller and the TV.

 

 

HITACHI Projection Television incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal power surges.

If your TV appears A LOSS OF POWER, please follow the following procedure:

1.Press the POWER button once.

2.If there is still no power, wait for 30 seconds and press the POWER button again.

3.If there is still no power, unplug the power cord from the wall outlet. Wait for 30 seconds and plug the power cord in. Press the POWER button again.

The protective technology should provide you for years of lasting entertainment from your HITACHI Projection Television.

The following phenomena are not failures:

1 The picture will appear after a while when the power is on.

2The cabinet clicks. The clicking is a creaking sound produced when the cabinet expands or contracts due to changes in temperature.

3Unevenness in color sometimes develops in part of the screen. Such unevenness in color may occur depending upon the nature or setting of the picture. The proper color may be restored by reducing the contrast or adjusting other settings.

4The TV set can generate sound distortion in external devices such as a radio. Please separate radio equipment from the TV set to a considerable distance.

Accessories

 

No.

 

 

 

Description

 

 

 

Quantity

 

 

 

C43-FD7000

 

 

 

C50-FD7000

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Instruction manual

2 Remote control unit (CLE-959)

3 Battery (For CLE-959)

4 IR BLASTER cable

5 Caster holder

6 Antenna adapter

1

 

Yes

 

Yes

 

 

 

 

 

1

 

Yes

 

Yes

 

 

 

 

 

2

 

Yes

 

Yes

 

 

 

 

 

2

 

Yes

 

Yes

 

 

 

 

 

4

 

Yes

 

Yes

 

 

 

 

 

1

 

Yes

 

Yes

 

 

 

 

 

54

Image 54
Contents C43-FD7000 C50-FD7000 Contents Safety Tips Safety Tips Safety Tips Safety Tips Before Using this Rear Projection TV LocationBest spot for viewing Precautions when using the batteries Connect the power cord and the antennaPrecautions when connecting the antenna Precautions when using the remote control unitFunctional PARTS Control panel and side panelProgram UP/DOWN buttons to Functional Parts Rear panelOn the remote control unit When the SET is AT Standby Power on/offTo Turn the Power on To Turn the Power OFFGetting Started Instructions for operating menuSelecting the on-screen display language MenuEasy Preset EnterON-SCREEN Display Menu Picture Menu Picture MenuIf the option of Reset was selected and press the Enter When the Color Manager option shown on the right isSet to On, you can adjust and balance their individual Top right to select the Color Manager option, then pressAudio Menu USP4638258 and 4482866. BBE and BBE symbol areON-SCREEN Display Menu Audio Menu Labs, IncOff Timer ON-SCREEN Display Menu Timer MenuTimer Menu On TimerON-SCREEN Display Menu Function Menu Function MenuON-SCREEN Display Menu Setup Menu 3UHVHW ŹPress Cursor buttons to select the Program 5.5, 6.0 or 6.5 Note Here the unit MHz is omitted Press the Ÿ ź cursor buttons to select the Sound SystemSECAM, NTSC4.43 or NTSC3.58 TV/VIDEO HighAntenna All Program PAL, SECAM, NTSC4.43 or NTSC3.58LQH7XQLQJ 3URJFKDQJH LQH7XQLQJ Easy Preset Refer to Auto Link Audio Out ON-SCREEN Diplay Menu Setup MenuSpeaker Fixed or VariableSave your adjusted data and exit from adjustment mode Magic FocusMulti Picture SplitMulti PIC P in P mode, you can press TV Scan Function ModeTV Scan Strobe function is shown as below AV NET Connection of the external audio/video equipmentAV NET Device External equipment Using the AV NET function  EnterQSXW DVD player’s Button. Press the Ÿ ź Ż Ź cursor  6XFFHHGHG External audio/video equipment type code UDQGWOHFWURQLF $PSOLIHU  $95HFHLYHU AV NET Teletext Other Functions Recall button TV/VIDEO buttonCH I/II button Size buttonŸP+ When non HD component signal is receivedWhen HD component signal is received 3Zoom +3Connection with Other Equipment Jacks and connections of side panelTypical connection of video camera or VCR, etc Connection with Other EQUIPMENT Jacks and connections of rear panelTypical connection of rear panel Typical connection of79$6&175 About the jacks and connections of rear panel VideoGuide to simple problem solving AccessoriesAddenda Specifications ADDENDAExemptions