Samsung HCM 4216W, HCM 422W Connecting a Camcorder, Connecting a Second VCR to Record from the TV

Page 19

I N S T A L L AT I O N

Connecting a Second VCR to Record from the TV

Your TV can send out signals of its picture and sound to be recorded by a second VCR. To do this, connect your second VCR as follows:

1

Connect a set of audio cables between the AUDIO OUT jacks on the TV and the AUDIO IN jacks on the VCR.

(The VCR input jacks might be either on the front or rear of the VCR.)

2

Connect a video cable between the

VIDEO OUT jack on the TV and the

VIDEO IN jack on the VCR.

Refer to your VCR’s instructions for more information about how to record using this kind of connection.

Connecting a Camcorder

The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR.

1

Locate the A/V output jacks on the camcorder. They are usually found on the side or rear of the camcorder.

2

Connect an audio cable between the AUDIO OUTPUT jack on the camcorder and the AUDIO terminals on the side of the TV.

If you have mono camcorder, connect L(mono) to camcorder audio out using only one audio cable.

3

Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the VIDEO terminal on the sidet of the TV.

The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables.

Note: This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be different, depending on the model.

CHAPTER TWO: INSTALLATION 2.6

Image 19

Contents Owner’s Risk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding Safety Your New TV InstallationOperation Troubleshooting Special FeaturesChapter One List of FeaturesFamiliarizing Yourself with The TV Audio Input jacks Using the Component ShelfFront or Side Panel Jacks ´ Video Input jackVideo Input jacks Rear Panel JacksAntenna terminals ¨ Audio Input jacks ´ AUDIO-VIDEO Monitor Output jacksStillMain Remote ControlPower ´ +100¸ P.Mode ± Mode˘ R.surf ¿ S.ModeAntennas with 300-ohm Flat Twin Leads Connecting VHF and UHF AntennasCable without a Cable Box Connecting Cable TVAntennas with 75-ohm Round Leads Separate VHF and UHF AntennasANT IN, VHF IN, or simply, Connecting to a Cable Box that Descrambles Some ChannelsCable with a Cable box that Descrambles All Channels This terminal might be labeledInstall AT I O N Connecting a VCR Connecting a Second VCR to Record from the TV Connecting a CamcorderConnecting to Y, PB, PR Connecting a DVD Player, DTV Set-Top Box 480i, 480pConnecting a DTV Set-Top Box 480p Install two AAA size batteries Replace the cover Installing Batteries in the Remote ControlMake sure to match the + Turning the TV On and Off Plug & Play FeatureYou can also use the Power button on the front panel Press the Power button1Press the Menu button CH or CH button. refer to Setting the clock onYou can also select Perfect Using the Perfect Focus FeatureFocus by pressing the Perfect Focus button Adjusting Manual Convergence If a horizontal red line is visible, use Adjust Red ConvergenceViewing the Menus Viewing the Menus and On-Screen DisplaysViewing the Display Selecting the Antenna Input Selecting a Menu LanguageMemorizing the Channels Selecting the Video Signal-sourceTV automatically cycles Storing Channels in Memory Automatic MethodAdding and Erasing Channels Manual Method Changing Channels Using the Channel ButtonsUsing the Number Buttons Using the Previous ChannelTo View Your Favorite Channels Selecting Your Favorite ChannelsTo Store Your Favorite Channels Can be set as Favorite channelsAdding and Erasing Channels Manual Method Select Channel, then Labeling in the A/V modeLabeling the Channels Press CH or CH to tune to the channel that will be labeledGauge will automatically disappearafter about 4 seconds After adjusting an item,Picture Control Customizing the PicturePress the Menu button. Picture icon will be high- lighted Using Automatic Picture SettingsSelecting the Color Tone Adjusting the VolumeUsing Mute Sound ControlPress the Menu button exit Customizing the SoundUsing Automatic Sound Settings Sure to select the proper time of day AM or PM Setting the ClockOption 1 Setting the Clock Manually When selecting the hours, bePress the VOL + button to select Auto clock set On Press the MenuPress the CH button to select Time Zone Star icon*will appear Fine Tuning ChannelsAfter you adjust the fine tuning Press the VOL + or VOL button to adjust the fine tuningDigital Noise Reduction Press the Aspect button to change the screen Changing the Screen Size43 TV Wide TVUsing the R.surf feature Before using the timer, you must Setting the On/Off TimerSelect Function, then If no function buttons Setting the Sleep TimerTo deactivate the On time Select Off during this stepSurround Extra sound settings Surround, Auto Volume, Melody, BBEChoosing a Multi-Channel Sound MTS Soundtrack Quick way to access the MTSSelect Caption or Text Viewing Closed CaptionsDifferent channels and fields Select Mode, then pressActivating Picture-in-Picture Quick way to access the PIPMenu Simply press the PIP button on the remote control Viewing Picture-in-PictureImage is the same as the main image Selecting a Signal Source Antenna or Cable for PIPSelecting a Signal Source External A/V for PIP Quick way to access the signalChanging the Size of the PIP Window Swapping the Contents of the PIP Image and Main ImageScanning the Available Channels Simply press the PIP CH button on the remote controlChanging the Location Rotating in PIP mode Changing the PIP ChannelMenu Simply press the V.Chip button on the remote control Using the V-ChipSetting Up Your Personal ID Number PIN Quick way to access the V-ChipHow to Set up Restrictions Using the TV guidelines How to Enable/Disable the V-ChipTV-14 TV Guidelines screen will appearGeneral audience Parent GuidanceOr CH Mpaa rating screen will appear Select Demonstration Viewing the DemonstrationPicture icon will be Highlighted blinkingMake sure you enter 3 digits Customizing Your Remote ControlSetting Up Your Remote Control to Operate Your VCR or DVD Remote control has fourSetting Up Your Remote Control to Operate Your Cable Box DVD Codes VCR CodesCable Box CodesChapter Five Identifying ProblemsUsing Your TV in Another Country Cleaning and Maintaining Your TVSpecifications