Programming the Macro Keys, Volume Lock

CD to DVD/LD SETUP* - 992 - DVD/LD - CD - CD - SETUP* - DVD or LD Player code

CD to RCVR SETUP* - 992 - RCVR - CD - CD - SETUP* - Audio

code

CD to CBL/SAT SETUP* - 992 - CBL/SAT - CD - CD - SETUP* - Cable/DBS code

CBL/SAT to TV SETUP* - 992 - TV - CBL/SAT - CBL/SAT - SETUP* - TV code

CBL/SAT to VCR SETUP* - 992 - VCR - CBL/SAT - CBL/SAT - SETUP* - VCR code

CBL/SAT to DVD/LD SETUP* - 992 - DVD/LD - CBL/SAT - CBL/SAT - SETUP* - DVD or LD code

CBL/SAT to RCVR SETUP* - 992 - RCVR - CBL/SAT - CBL/SAT - SETUP* - Audio code

CBL/SAT to CD SETUP* - 992 - CD - CBL/SAT - CBL/SAT - SETUP* - CD Player code

*NOTE: Here (*) you must hold SETUP until the Cinema 6+’s red light blinks twice.

PROGRAMMING THE MACRO KEYS

The Cinema 6+ has two Macro keys (MACRO and MACRO2) that allow the user to play back a series of key- strokes, at any time, with the press of one key. For example, to set up a sequence that will turn on your components and change the components to the proper inputs:

1.Press and hold SETUP until the Cinema 6+’s red light blinks twice, then release SETUP.

2.Press 9 - 9 - 5. The Cinema 6+’s red light will blink twice.

3.Press and release one of the MACRO keys. This will be the key that will play back the series of key- strokes assigned to that key.

4.Begin entering the sequence of keystrokes, up to 15, that you wish to be played back when you press the MACRO key. For example:

RCVR – POWER – TV – POWER – TV/VCR (To change the input on the TV to VIDEO 1) – CBL/SAT

– POWER.

5.Once your sequence is entered, press and hold SETUP until the Cinema 6+’s red light blinks twice.

Now, using the example as above, whenever the pro- grammed MACRO key is pressed, the Receiver would power ON, the TV will power ON and change the input to VIDEO 1 and then the Satellite would power ON.

Repeat steps 1 - 5 to then setup a second sequence on the MACRO2 key.

VOLUME LOCK

Volume Lock allows the user to designate which component will control the volume in the TV, DVD/LD and CBL/SAT modes. To set the Volume Lock to the TV mode:

1.Press and hold SETUP until the Cinema 6’s red light

blinks twice, then release SETUP.

Web Site : http://www.oneforall.com

2.Press 9 - 9 - 3. The Cinema 6+’s red light will blink twice.

▲

3.Press and release TV. The Cinema 6+’s red light will blink twice.

Now, whenever you press VOL , VOL or MUTE in the VCR, DVD/LD and CBL/SAT modes your TV will control the volume. If you would like to change the Volume Lock setting to the VCR, DVD/LD or CBL/SAT modes repeat steps 1-3, only substitute the appropriate device key. Setting the Volume Lock to the TV, VCR, DVD/LD or CBL/SAT mode will not effect the volume control in the RCVR and CD mode.

You can also change the Volume Lock setting so that an Audio component controls the volume in all device modes.

To change the Volume Lock setting on the Cinema 6+ to the RCVR mode:

1.Press and hold SETUP until the Cinema 6+’s red light blinks twice, then release SETUP.

2. or Press 9 - 9 - 3. The Cinema 6+’s red light will blink twice.

3.Press and release RCVR▲. The Cinema▲ 6+’s red light will blink twice.

Now, whenever you press VOL , VOL or MUTE your Audio component will control the volume in all device modes.

You can also change the Volume Lock setting so that each component controls its own volume. However, some compo- nents do not have volume control. Using this setting may eliminate volume control in some device modes. To change the Volume Lock setting on the Cinema 6+ so each mode controls its own volume:

1.Press and hold SETUP until the Cinema 6+’s red light blinks twice, then release SETUP.

▲

2. Press 9 - 9 - 3. The Cinema 6+’s red light will blink twice.

	▲	▲
3.	Press and release VOL . The Cinema 6+’s red
	light will blink twice.
Now, whenever you press press VOL , VOL		or MUTE on

the Cinema 6+ each component will control its own volume, provided each component has volume control.

Web Site : http://www.oneforall.com