One for All URC8820N warranty Programming Favorite Channel Scan, Re-Assigning Device Keys

Page 12

Programming Favorite Channel Scan

In the TV, VCR, DVD, and CBL/SAT modes, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when you press FAV (see “Using Channel Scan”).

NOTE: Only channels of one mode can be stored for Favorite Channel Scan.

1.On the remote control, press TV, VCR, DVD, or CBL/SAT once.

2.Press and hold SET until the LED (red light) blinks twice, then release SET.

3.Enter 9 9 6. The LED will blink twice.

4.Use the keypad to enter a favorite channel number (e.g., 031). Then press SET once.

NOTE: If the original remote control required pressing an ENTER key to change the channel, also press the ENTER key after the channel number (e.g., 0 3 1 ENTER).

5.If desired, repeat step 4 (in this section) for each favorite channel to be stored, up to a total of 10 channels.

NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming.

6.To exit programming, press and hold SET for 3 seconds. The LED will blink twice.

Re-Assigning Device Keys

You can set this remote to control a second TV, VCR, DVD player, or other device. For example, to control a TV, a cable box, and two DVDs, you will need to re-assign the AUX key to operate the second DVD as follows:

1.On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET.

2.Enter 9 9 2. The LED will blink twice.

3.Press DVD once, then press AUX once.

4.The AUX key is now ready to be programmed for your second DVD. See “Setting Up Your Components.”

To re-assign other device keys to the AUX key, repeat steps 1 through 4 by substituting the sequence from the following chart:

To Re-Assign Device

Perform Sequence

 

 

AUX as 2nd TV key:

SET - 9 - 9 - 2 - TV - AUX

 

 

AUX as 2nd VCR key:

SET - 9 - 9 - 2 - VCR - AUX

 

 

 

AUX as 2nd CBL/SAT key:

SET - 9 - 9 - 2

- CBL/SAT - AUX

 

 

 

AUX as 2nd CD key:

SET - 9 - 9 - 2

- CD - AUX

 

 

 

AUX as 2nd PVR key:

SET - 9 - 9 - 2

- PVR - AUX

 

 

 

AUX as 2nd AUD key:

SET - 9 - 9 - 2

- AUD - AUX

 

 

 

You can also re-assign another unused device key by substituting an open key for the AUX key in the above chart and performing the sequence. For example, to re-assign an unused CBL/SAT key as a 2nd CD key, perform SET - 9 - 9 - 2 - CD CBL/SAT. When a re- assignment is done, the LED (red light) will blink twice to confirm your choice. At that time, you will need to program the remote control for the new device (see “Setting Up Your Components”).

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Contents ContenidoInstalling Batteries Features and FunctionsIntroduction Key Charts Device Table Device Controls These Devices KEYSetting Up Your Components Programming Combo Device Control Searching For Your CodeCBL/SAT Code To control a TV/DVD ComboUsing Learning Learning PrecautionsChecking the Codes Changing Volume Lock Locking Volume Control To One Mode Global Volume LockProgramming a Learning Key Deleting Functions From The Learning Keys Unlocking All Volume Control Restoring Default Setting Programming a Favorite ChannelProgramming a Master Power Macro To Program the Master Power MacroTo Operate Master Power Macro Programming a Macro On a Device KeyUsing Channel Scan Clearing a MacroTo Program the Device Key Macro To Operate the Device Key MacroProgramming Favorite Channel Scan Re-Assigning Device KeysAUX as 2nd CD key SET 9 9 CD AUX AUX as 2nd PVR key AUX as 2nd AUD key SET 9 9Using Keymover Restoring Factory Default SettingsRestoring Keymoved Keys To Default Settings Programming KeymoverTroubleshooting FCC ComplianceCare and Maintenance Additional InformationLimited Lifetime Warranty Introducción Instalación de las BateríasCaracterísticas y Funciones De Encendido Maestro en la tecla Power Funciones de las TeclasTabla de Dispositivos Tecla DE Controla Estos DispositivosProgramación de un Dispositivo Aparato Programación de un Aparato Combinado Búsqueda de su CódigoPara controlar un aparato combinado TV/DVD Uso de la Función Aprendizaje Verificación de los CódigosPrecauciones sobre la Función Aprendizaje Cambio del Bloqueo del Volumen Programación de una Tecla de AprendizajeBorrar Funciones de las Teclas de Aprendizaje Uso de los Macros Programación de un Macro de Canal FavoritoUso del Macro de Encendido Maestro en la Tecla Power Programación de Un Macro en una Tecla de DispositivoPara Programar el Macro de Encendido Maestro en la Tecla Uso de la Exploración de Canales Borrar un MacroPara Programar el Macro de Tecla de Dispositivo Uso del Macro de Tecla de DispositivoProgramación de una Exploración de Canales Favoritos Reasignación de las Teclas de DispositivosAUX como la 2a tecla CD SET CD AUX AUX como la 2a tecla PVR AUX como la 2a tecla AUD SETUso de la Función Keymover Programación de la Función KeymoverRestauración de una Sola Tecla Mudada Restauración de Todas las Teclas Mudadas en un Solo ModoRestauración de los Valores Fijados en la Fábrica Localización de FallasConformidad con la FCC Información AdicionalCuidado y Mantenimiento Garantía Limitada durante la Vida Útil del Producto Page Audio DTV ConvertersRécepteurs TV numériques Convertidores DigitalesVCRs / Magnétoscopes DVD / Lecteurs DVDPVRs DVRs Plasma
Top Page Image Contents