One for All URC8820N warranty Troubleshooting, FCC Compliance

Page 14

Troubleshooting

LED (red light) does not blink when you press a key.

Replace batteries with two new AAA alkaline batteries.

LED (red light) blinks five times after you press a key.

Replace batteries with two new AAA alkaline batteries.

LED blinks when you press a key, but home entertainment device does not respond.

Make sure the remote control is aimed at your home entertainment device and is not farther than 15 feet away.

The unit does not control home entertainment devices or commands are not working properly.

Try all listed codes for the device brands being set up. Make sure they can be operated with an infrared remote control.

TV/VCR Combo does not respond properly.

Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation.

Changing channels does not work properly.

If the original remote control required pressing ENTER to change channels, then press ENTER on the remote control after entering the channel number.

During learning, LED emits a long blink after pressing and holding key to be learned.

Memory is full or a bad capture has occurred. Avoid high-ambient light sources, such as direct daylight and fluorescent bulbs. Try readjusting positions of remote controls before performing the procedure again.

Tried Searching For Your Code method and still could not find a working code.

Clear the device key as follows: Press and hold SET until the LED (red light) blinks twice, then release.Next enter 9 9 2. Then press the device key to be cleared twice.Now repeat the Searching for Your Code method.

No remote control of volume.

See “Changing Volume Lock” to lock/unlock volume.

If the above does not work.

Please visit: www.oneforall.com

Consumer Help Line: 1 (800) 315-0990

FCC Compliance

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Contents ContenidoIntroduction Installing BatteriesFeatures and Functions Key Charts Device Table Device Controls These Devices KEYSetting Up Your Components CBL/SAT Code Programming Combo Device ControlSearching For Your Code To control a TV/DVD ComboChecking the Codes Using LearningLearning Precautions Programming a Learning Key Changing Volume LockLocking Volume Control To One Mode Global Volume Lock Deleting Functions From The Learning KeysUnlocking All Volume Control Restoring Default Setting Programming a Favorite ChannelTo Operate Master Power Macro Programming a Master Power MacroTo Program the Master Power Macro Programming a Macro On a Device Key To Program the Device Key Macro Using Channel Scan Clearing a Macro To Operate the Device Key MacroAUX as 2nd CD key SET 9 9 CD AUX AUX as 2nd PVR key Programming Favorite Channel ScanRe-Assigning Device Keys AUX as 2nd AUD key SET 9 9Restoring Keymoved Keys To Default Settings Using KeymoverRestoring Factory Default Settings Programming KeymoverTroubleshooting FCC ComplianceCare and Maintenance Additional InformationLimited Lifetime Warranty Características y Funciones IntroducciónInstalación de las Baterías De Encendido Maestro en la tecla Power Funciones de las TeclasTabla de Dispositivos Tecla DE Controla Estos DispositivosProgramación de un Dispositivo Aparato Para controlar un aparato combinado TV/DVD Programación de un Aparato CombinadoBúsqueda de su Código Precauciones sobre la Función Aprendizaje Uso de la Función AprendizajeVerificación de los Códigos Borrar Funciones de las Teclas de Aprendizaje Cambio del Bloqueo del VolumenProgramación de una Tecla de Aprendizaje Uso de los Macros Programación de un Macro de Canal FavoritoPara Programar el Macro de Encendido Maestro en la Tecla Uso del Macro de Encendido Maestro en la Tecla PowerProgramación de Un Macro en una Tecla de Dispositivo Para Programar el Macro de Tecla de Dispositivo Uso de la Exploración de CanalesBorrar un Macro Uso del Macro de Tecla de DispositivoAUX como la 2a tecla CD SET CD AUX AUX como la 2a tecla PVR Programación de una Exploración de Canales FavoritosReasignación de las Teclas de Dispositivos AUX como la 2a tecla AUD SETRestauración de una Sola Tecla Mudada Uso de la Función KeymoverProgramación de la Función Keymover Restauración de Todas las Teclas Mudadas en un Solo ModoRestauración de los Valores Fijados en la Fábrica Localización de FallasCuidado y Mantenimiento Conformidad con la FCCInformación Adicional Garantía Limitada durante la Vida Útil del Producto Page Récepteurs TV numériques AudioDTV Converters Convertidores DigitalesPVRs DVRs VCRs / MagnétoscopesDVD / Lecteurs DVD Plasma
Top Page Image Contents