JVC HD-56FH97 manual LAMP/PROGRAM LED blinks, Power LED and LAMP/PROGRAM LED blink alternately

Page 89

Lamp Replacement

Warning LED Messages

While the power is on, and there is a problem with the TV, the TV changes to warning mode and informs you of the problem using the LED as follows. Then, the power turns off automatically and performs the cooling for approximately 1 minute.

The LAMP/PROGRAM LED blinks

Condition: It may be a malfunction of the internal electrical circuits.

To correct: Keep the TV off for a while and then turn the power on again. If the TV goes into warning mode, unplug the TV after the cooling has completed and consult your dealer.

The POWER LED and LAMP/PROGRAM LED blink alternately

Condition: The inside temperature rises abnormally or the fan may be blocked.

To correct: Keep the TV off for a while and then turn the power on again. If the TV goes into warning mode, unplug the TV after the cool down as completed and consult your dealer.

The POWER LED and LAMP/PROGRAM LED blink rapidly simultaneously

Condition: The lamp unit has been installed on a slant and is not flat, or it is not fully inserted into the lamp housing. Or it may be a lamp malfunction.

To correct: • If this condition occurs soon after replacing the lamp: Reinstall the new lamp unit. Repeat the lamp installation steps, taking care to observe all warnings. Make sure the lamp sits FLAT inside the unit when you reinstall it.

If this condition occurs except for replacing the lamp: Keep the TV off for a while and then turn the power on again. If the TV goes into warning mode, unplug the TV after the cool down as completed and consult your dealer.

89

Downloaded from www.Manualslib.com manuals search engine

Image 89
Contents Projection Television Users Guide Important Safety Precautions Important Safety Instructions FCC Notice Caring for the Screen Caring for the CabinetOrder to use the television for a long time When the power is turned on, the warming up commencesCooling the inside of the television and the lamp Lamp is a consumable itemILA element characteristics Television requires a lot of electrical powerScreen is made of plastic Do not replace the lamp immediately after useTable of Contents Unpacking your TV Quick SetupTV Models Rear Panel DiagramSide Panel Diagram Front Panel DiagramModels HD-56FC97, HD-61FC97, HD-70FH97, HD-70FN97 Models HD-56FH97, HD-61FH97, HD-56FN97, HD-61FN97Power Remote ControlGetting Started Key Feature ButtonsBasic Operation Coaxial Cables Connecting Your DevicesVideo Cable Component Cables Composite Cables Audio CablesVCR Connection Diagram #2 Connecting to Monitor/Recording Output Terminal Connecting to a Camcorder Connecting to an External Amplifier Connecting to the Surround AmplifierConnecting to an amplifier using your optical output Connecting to a Digital TV Receiver Connecting to an Hdmi Compatible Device OUT TV Rear Panel Looking at the images from a computer Connecting to the computerWhen a picture is not displayed Table of signals for each type of computerInteractive Plug In Menu LanguageTo be Manual Clock Set Auto Clock SetNOW Programming Auto Tuner SetupCable Box or Satellite Codes Remote ProgrammingMGA VCR CodesSMC DVD CodesVCR/DVD Search Codes Function Search Codes Cable/Satellite Search Codes FunctionOnscreen Menus Using the GuideOnscreen Menu System Onscreen Menu SystemSelected Option Green Selected Option BlueInitial Setup CLOCK/TIMERS To Initial SetupAuto Tuner Setup Analog Channels Channel SummaryContinue to follow these directions for all four spaces Chip Channel Guard MessageDirections to Block Unrated Programs Unrated ProgramsUS V-Chip Ratings Directions to set US V-Chip Ratings Setting US V-Chip RatingsDirections to set Movie Mpaa Ratings Movies RatingsDirections to set Canadian V-Chip Ratings Canadian V-Chip RatingsSet Lock Code Closed Caption Analog SettingLanguage If you want to cancel the settings, select cancel Digital Auto SettingDigital Manual Setting Noise Muting Auto Shut OffV1 Smart Input Front Panel LockVideo Input Label Power Indicator Position AdjustmentAudio Out Video-1 Monitor OutTV Speaker Digital-In1 Audio Digital-InCenter CH Input Digital SetupAspect Ratio Antenna LevelDigital Sound Link Auto Play Software UpdateCable Card Application Color Temperature Picture SettingsAdjust the Picture Settings Advanced Smart Picture Color ManagementDynamic Gamma Digital VNR ResetAdjust the Sound Settings Sound SettingsTurn On Volume Volume LimitThank YOU Set ClockOn/Off Timer Following message will appear Lamp Timer ResetTwin Multi Screen FunctionFreeze IndexSwap SelectNumber Buttons 10Key Pad PowerTune InputChannel + Volume +TheaterPro D6500K Return +/TVHD-61FN97 and HD-70FN97 only SoundMuting Natural Cinema Video StatusSleep Timer Message Sleep TimerDisplay Time Channel Off DisplayDelete the favorite channel FavoriteRegister the favorite channel Aspect Ratios Aspect Ratios in PC ModeAspect Back MenuVCR/DVD Slide Switch TV/CATV Slide SwitchVCR Buttons DVD ButtonsTo watch digital channels Digital CH D/A Digital/AnalogSub Channel GuideController Link MenuMovie DeviceReservation TimerTimer Edition Timer EditTimer Deletion Cancel the timer recordingNo Program Weak SignalInvalid Signal Cable Card Connection Cable Card InformationChanging the Lamp Lamp ReplacementLamp Message Replacement Lamp KitRemove the lamp cover How to Replace the LampUnplug the television Remove the lamp unit Install the new lamp unitLAMP/PROGRAM LED blinks Power LED and LAMP/PROGRAM LED blink alternatelyPower LED and LAMP/PROGRAM LED blink rapidly simultaneously Troubleshooting Following are not malfunctions Problems CheckSpecifications subject to change without notice SpecificationsOutput Page Page JVC Company of America JVC CANADA, INC
Related manuals
Manual 96 pages 57.7 Kb