HDMI connections (continued) | Page | |
When playing | ≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting. | 24 |
progressive output, one part of | 1 Connect this unit to the TV with any cable except the HDMI cable. |
|
the picture momentarily | 2 When you connect with the Component Video cable, set “HDMI Video Mode” to “Off” and |
|
appears to be doubled up. | “Component Resolution” to “576i/480i” in the Setup menu. |
|
No sound. | ≥Audio may not be heard when more than 4 devices are connected with HDMI cables. | — |
Low volume. | Reduce the number of connected devices. | — |
Distorted sound. | ≥The sound effects will not work when the bitstream signal is output from the HDMI AV OUT | |
Cannot hear the desired audio | terminal or the DIGITAL AUDIO OUT terminal. | 24 |
type. | ≥To output audio from a device connected with an HDMI cable, set “HDMI Audio Output” to | |
| “On” in the Setup menu. | 25 |
| ≥If the sound is distorted when the unit is connected to an amplifier/receiver with an HDMI | |
| cable, adjust the settings in “Speaker” in the Setup menu to match the connection. | — |
| ≥Depending on the connected equipment, the sound may be distorted if this unit is connected | |
| with an HDMI cable. | 23 |
| ≥When | |
|
| |
| converted to 5.1 channel audio. In this case, set the |
|
Card |
|
|
The capacity of the SD card | ≥When a | 13 |
decreased. | data may be written to the SD card. Erase the data by using |
|
| the card or use a new card. |
|
≥Data that can be played from an SD card are AVCHD and JPEG data. | 5 | |
music on an SD card cannot be |
|
|
played. |
|
|
The contents of the card | ≥The card is not compatible or the contents on the card may be damaged. | 5 |
cannot be read. | ≥Turn off and then turn on the unit again. | — |
Other difficulties with playback |
| |
Audio and video momentarily | ≥This occurs between playlist chapters or scenes ([AVCHD]). | — |
pause. | ≥When playing a title recorded on both layers, the unit automatically switches between layers | — |
| and plays the title in the same way as a normal programme. However, video and audio may |
|
| momentarily cut out when the unit is switching layers. |
|
| ≥Ensure the disc is for the correct | Cover |
played. | not defective. | 22 |
| ≥You have set a ratings level to limit | |
| ≥Some | — |
≥Confirm whether the disc supports | — | |
with |
|
|
The virtual package | ≥Confirm whether the disc supports the virtual package. | 13 |
is not played with | ≥The inserted SD card does not have sufficient available capacity. | — |
| ≥The SD card is | 5 |
| ≥Sub contents copied to an SD card are provided by the disc producer as a part of the | 13 |
|
| |
| as a virtual package. |
|
Alternative soundtrack and | ≥The languages are not recorded on the disc. | — |
subtitles cannot be selected. | ≥You may not be able to use the | 11, 13 |
| some discs. Use the disc’s menus to make changes. |
|
No subtitles. | ≥Subtitles are not recorded on the disc. | — |
| ≥Turn the subtitles on. Set “Subtitle” on the | 20 |
Angle cannot be changed. | ≥Angles can only be changed during scenes where different angles are recorded. | — |
The resume play function does | ≥Memorized positions are cancelled when | — |
not work. | – pressing [∫] several times. |
|
| – opening the disc tray. | — |
| ≥The resume play function may not work depending on the disc. |
When other Panasonic products respond to this remote control
Change the remote control code on the main unit and the remote control (the two must match) if you place other Panasonic products close
together.
1Press [SETUP].
2Press [3, 4] to select “General” and press [OK].
3Press [3, 4] to select “Remote Control” and
press [OK].
4Press [3, 4] to select the code (1, 2, or 3) and press [OK].
5To change the code on the remote control
While pressing [OK], press and hold the numbered button ([1], [2] or [3]) for more than
5seconds. 6 Press [OK].
Remote Control
Set Code 1
Set Code 2
Set Code 3
Press [] and [OK] together for more than 5 seconds on
the remote.
When the following indicator
appears on the unit’s display and you are unable to operate the unit
NOTE
D
R
The unit’s remote control code
Press and hold [OK] and the indicated number button at the same time for more than 5 seconds.
Reference
RQT9038
29