Philips DVP620VR manual Programmed Playback CD MP3 Jpeg, Slide Show Mode, On-Screen Information

H9723AD(EN).qx3 04.6.25 3:28 PM Page 15

Playing a Disc

Programmed Playback CD MP3 JPEG

You may determine the order in which tracks will be played.

1In stop mode, press MODE.

• The PROGRAM screen will appear.

2Press ▲ or ▼ to select a track, then press OK.

• Up to 99 tracks can be stored.
		CD-DA	TOTAL 0:03:30
• Press CLEAR/C-RESET to		T	T
erase the most recently		T
		T
		T
entered programme.		T
		T
• To erase all tracks in the	OK	T
programme at once, select
		T
“ALL CLEAR” at the bottom
of the list and press OK.

•When selecting an MP3 or JPEG file or folder, use Arrow as follows: Press B to go the next hierarchy.

Press s to go back to the previous hierarchy.

•To check programmed tracks or files, , 3 to change the pages.

3Press PLAY B to start the programmed playback.

Notes:

-While a programme is being played back, STOP C works as follows:

Press STOP C, and then PLAY B next, so that the programmed playback restarts.

(CD playback restarts from the current position. MP3 playback restarts from the beginning of the current track.) Press STOP C twice and PLAY B next, so that playback restarts from the first track in the original order. However, your programmed playback can be restarted when you follow the above steps. (Your programme is still stored unless either the disc tray is open or the unit is turned off.)

-To repeat the current track in the programme, press REPEAT repeatedly until “ TRACK” appears during playback.

-To repeat the entire programme press REPEAT repeatedly until “ ALL” appears during playback.

-The system can recognise up to 255 groups/ folders and up to 512 tracks/ files, and this applies even to the case where mixed MP3 and JPEG files are recorded.

-Up to 8 hierarchies can be created.

-If a JPEG file is selected, the image will be reproduced from the selected track and go to the next one in turn. A track is displayed for 5 seconds and then the next track is displayed.

Each press on the cursor button B will rotate the image clockwise by 90 degrees when an image is displayed. Each press on the cursor button s will rotate the image counterclockwise by 90 degrees.

For best results use files recorded at these specifications:

[MP3]

•Sampling frequency: 44.1kHz or 48kHz

•Constant bit rate: 112kbps ~ 320kbps.

[JPEG] size of image

• Upper limit:	6,300 x 5,100 dots.
• Lower limit:	32 x 32 dots.

Slide Show Mode JPEG

You can switch the slide show modes during playback.

1Press the MODE button during playback.

•The slide show mode screen will appear.

•The slide show mode cannot be switched when it is stopped, or from the file list screen.

2Press the OK button.

•The slide show mode will change.

“CUT IN/OUT”: The entire image appears in one time.

“FADE IN/OUT”: The image appears gradually and then disappears.

3Press the MODE button to exit.

On-Screen Information

You can check information about the current disc by pressing DISPLAY on the remote control.

Random Playback CD

This shuffles the playing order of tracks instead of playback in the sequence.

1In stop mode, press MODE twice.

• RANDOM screen appears.

2Press PLAY B to start random playback.

MP3 JPEG

RANDOM

CD-DA TOTAL 0:45:55

RANDOM PROGRAM

-- no indication --

PLAY

DVD-V

1	Press DISPLAY during playback to show current Chapter.
	• The elapsed and remaining time of the current chapter will
	be displayed.
2	Press DISPLAY again to show current title.
	• The elapsed and remaining time of the current title will be
	displayed.
3	Press DISPLAY again.
	• The BIT RATE and the current repeat setting will be

Note:

-If you like to repeat the current track in the random selection, press REPEAT repeatedly until “ TRACK”

appears during playback. If you like to repeat the entire random selection press REPEAT repeatedly until “ ALL” appears during playback.

MP3/JPEG Playback MP3 JPEG

Insert an MP3 or JPEG disc, then press MENU to call up the MP3 or JPEG menu on the TV screen.

1In stop mode, press K or L to

select the desired group, MP3	FILE LIST
track or JPEG file.
	FOLDER	DISC NAME
• If a group is selected, press PLAY	MP3
	JPEG	folder name 1
B or OK to go on to the track		folder name 2
		folder name 3
		folder name 4
selection screen. Press K or L		file name 1
		file name 2
to choose a track, then press	OK	file name 3
		1/2
PLAY B or OK.	PLAY	folder name 1

•If a track is selected, press B or OK to start playing from the track.

•Press TITLE to return to the first item. 2 Press STOP C to stop playback.

Notes:

-Folders are known as Groups; files are known as Tracks.

-The “ ” symbol is shown on the top of the group name.

- The “ 3 ” symbol is shown on the top of MP3 files. - The “ ” symbol is shown on the top of JPEG files.

displayed.

• If you are playing a dual layered disc, the layer number will

also be displayed ( L0: Layer 0 is playing. L1: Layer 1 is playing).

4 Press DISPLAY again to remove the display.

CD VCD

1Press DISPLAY during playback, the current track will be displayed on the TV screen.

•The elapsed and remaining time of the current track will be displayed.

2Press DISPLAY again to show the total time of the disc.

•The elapsed and remaining time of the current total track will be displayed.

3Press DISPLAY again to remove the display.

MP3 JPEG

1Press DISPLAY.

• The name of the file currently in play will be displayed.

2Press DISPLAY again to show the track number, the elapsed time, the repeat status, and the playback status at the top of the screen.

3Press DISPLAY again to exit.

Hints for the On-Screen Display

• C - indicates Chapter repeat.

• T - indicates Title / Track repeat

• G - indicates Group (folder) repeat

• A - indicates Disc repeat

•A B - indicates A-B repeat

15