Philips DVP620VR manual Automatic Channel Setup To Skip a Preset Channel, Setting the clock

H9723AD(EN).qx3 04.6.25 3:28 PM Page 8

Setting Up your DVD/ VCR

		Automatic Channel Setup					To Skip a Preset Channel
		You can programme the tuner to scan only the channels that					The channels you can no longer receive or seldom watch can
		you can receive in your area.					be set to be skipped when you access channels SKIP 3/CH K
		• Use the remote control for this procedure.					or SKIP	/CH L.
1 Turn on the TV and select the TV channel to the video channel						1	• Use the remote control for this procedure.
2	on the TV.						Press VCR, then MENU.
		Press VCR, then MENU.				2	Press K/L to select “INITIAL”, then press B.
3 Press K/L to select “INITIAL”, then press B.						3	Press K/L to select “CH TUNING”, then press B.
4		Press K/L to select “CH TUNING”,				4	Press K/L to select “MANUAL”, then press B.
5		then press B.		CH TUNING		5	Press K/L to select “SKIP”, then
		Press K/L to select “AUTO”, then		B AUTO		6	press B.			MANUAL
		press B.					Use numerical key pads or K/L to
				MANUAL						POSITION	P08
		• The tuner scans and memorises					select relevant position number,
										PPPPPPPPPPPPPPPP
		all the active channels in your					then press B.			BAND	[UHF]
		area. After scanning, the tuner				7	Press K/L to select “SKIP”, then			B SKIP	[OFF]
		stops on the lowest memorised					press B to select “ON”.
		channel.					• To memorise the channel again,
							press B. “ON” will change to “OFF”.
To Select a Desired Channel						8
							Press MENU to exit.
You can select a desired channel by using the SKIP 3/CH K or
							Note:
SKIP			/CH L, or directly pressing the numerical key pads on the
remote control.							– To confirm that a channel has been deleted, press SKIP
• Enter a channel numbers as a two-digit number for the quickest							3/CH K or SKIP		/CH L.
	results. For example, to select channel 6, press 0 and 6. If you
	only press 6, channel 6 will be selected after a brief delay.
							Setting the clock
• You can only select channels 1-99.
							If the display shows an incorrect time or “ --:-- ”, the time and
							date must be reset manually.
		Manual Channel Setup
							• This DVD/VCR incorporates a 24-hour clock.The clock must
		• Use the remote control for this procedure.
1							be set for the Automatic Timer Recording function to operate
		Press VCR, then MENU.					correctly.
2 Press K/L to select “INITIAL”, then press B.						1	Press VCR, then MENU.
3		Press K/L to select “CH TUNING”, then press B.				2	Press K/L to select “INITIAL”, then press B.
4 Press K/L to select “MANUAL”, then press B.						3	Press K/L to select “CLOCK”, then press B.
5		Press K/L to select “POSITION”,				4	PressK/L until the relevant year
		then press B.		MANUAL			appears, then press B.			CLOCK
		• When a weak signal is received in		B POSITION	P08	5	Likewise, set the relevant month,			B YEAR	2 0 0 4
		Manual Tuning mode, you can					day, hour, and minute.
				PPPPPPPPPPPPPPPP						MONTH	0 1
		change the background to solid		BAND	[UHF]	6	Press MENU to start the clock.			DAY	0 7 WE
		blue or the static screen by		SKIP	[OFF]		Notes:			HOUR	_ _
										MINUTE	_ _
		pressing CLEAR/C.RESET.
							– In the steps 4 and 5, you can
6 Use numerical key pads or K/L to
							go back to the item you want
		select your desired position number, then press B.
							to correct by pressing s .
		• You can select position number 01-99.
							– Although seconds are not displayed, they begin counting
		• If “ON” appears on the right side of “SKIP”, press K/L to
							from 00 when you exit by pressing MENU. Use this
		point to “SKIP”. Then press B to select “OFF”.
							feature to synchronise the clock with the correct time.
	• Press K/L to select “BAND”, then press B.
7							– When unplugging the power-cord or if there is a power
		Press K/L to select “PPPPPPPPPP”, then press s / B
							failure for more than 1 minute, you may have to reset
		to start scanning.
							the clock.
		• The DVD/VCR tuner will begin to search up or down
		automatically.When a channel is found, the DVD/VCR will
							Picture Select
		stop searching and the picture will appear on the TV Screen.

Tuner channel	VHF L:	45.75~138.25MHz
	VHF H:	140.25~423.25MHz
	UHF:	427.25~855.25MHz

8Press MENU to exit.

Note:

–To confirm that a channel has been added, press SKIP 3/CH K or SKIP /CH L.

This function enables you to select the picture quality of a tape.

•Use the remote control for this procedure. 1 Press VCR, then MENU.

2	Press K/L to select “SET UP”, then	MENU
	press B.
3
	Press K/L to select “PICTURE”,	TIMER
	then press B.	B SET UP
4 Press B until the desired mode		INITIAL
	(NORMAL, SOFT, or SHARP) is
	indicated on the TV screen.
	Notes:
	– If the On screen menu still	SET UP
	remains, press MENU to exit
	the menu.	AUTO REPEAT [ON]
	– Once you select the Picture	B PICTURE [NORMAL]

Select mode, it stays in effect even after you turn off the DVD/VCR.

– When you use this function

during playback, you can select a mode (NORMAL, SOFT or SHARP) as you watch video image.

8