Philips 26PFL4907 Channel installation, Autoprogram, Weak channel installation, Installation mode

Page 37

Channel installation

Be sure the RF cable is correctly connected to this unit and you are registered with your cable TV provider when you install cable channels.

Autoprogram

If you switch wires (e.g. between antenna and CATV) or if you move the unit to a different area after the initial setting, or if you restore the DTV channels you deleted, it is recommended to use AutoProgram to perform a new channel search.

You need to select the signal type in Installation mode before you perform AutoProgram.

1Use ▲▼ to select Channels, then press OK.

2 Use ▲▼ to select Autoprogram, then press OK.

• If you run Autoprogram when you have locked channels, a message appears asking to enter your PIN code. Enter your PIN code in order to complete the installation.You need to set the channel lock again after the installation.

3 Press OK to select Start now.

• When the scanning and memorizing are completed, the lowest memorized channel will be displayed.

4 Follow the on-screen instructions to complete the installation.

System searching. Please wait...

Digital channels found: 0

Analog channels found: 0

Auto programming may take more than 20 minutes to complete.

Stop

Note

••After setting Autoprogram, using CH +/− skips unavailable programs automatically.

••If you are not receiving a signal from your cable service, contact the cable provider.

••If you press or during AutoProgram, the setup of TV channels will be canceled.

••Even if Autoprogram is completed, the channel setting will be lost if the AC power cord is unplugged before the unit goes into Standby mode by pressing .

••The PIN code will be required once you set a PIN code in the Child and ratings lock.

p. 34

••If you want to change your PIN code, follow the instruction of Change PIN. p. 36

37

Weak channel installation

This function lets you add the channels that were not added by the AutoProgram due to the reception conditions during the initial setup. It is available only when you select Antenna in Installation mode.

1Use ▲▼ to select Channels, then press OK.

2 Use ▲▼ to select Weak channel installation, then press OK.

• The PIN code will be required if you have locked channels.

3 Use ◄► to select channel Input box, then use ▲▼ to select a channel you want to memorize.

4Use ◄► to select Search, then press OK.

5Display will be changed to Store from Search when the channel is found, then press OK.

Note

••In most cases, Digital channels are not broadcast on the RF channel on which they appear on your TV.To add Digital channels you need to know the RF channel on which the Digital channel is being broadcast. (e.g. If there is a Digital channel 9.1 which is being broadcast on RF channel 25, you need to enter 25 while performing a weak channel installation.) To find out the RF channel on which a particular Digital channel is being broadcast, please contact your local service provider.

Installing Digital channels using Weak channel installation might not work for direct cable connections and if the Digital signal is too weak for the TV to process.

Installation mode

1Use ▲▼ to select Channels, then press OK.

2Use ▲▼ to select Installation mode, then press OK.

3Use ▲▼ to select Antenna or Cable, then press OK.

When Antenna is selected, the TV detects antenna signals. It searches for DTV and Analog TV channels available in your area.

When Cable is selected, the TV detects signals supplied by cable. It searches for DTV Analog TV and Cable channels available in your area.

Uninstall channels

Those channels can still be selected with the NUMBER buttons.

1Use ▲▼ to select Channels, then press OK.

2Use ▲▼ to select Uninstall channels, then press OK.

3Use ▲▼ to select the channel you want to remove, then press OK.

You will not be able to select the channel again using CH +/−.

The removed channels are not displayed on the list of favorite channels.

To reactivate a removed channel, use ▲▼ then press OK.

English

Image 37
Contents Register your product and get support at Contents Product Safety Notification 22PFL4907 Wall Mount Bracket Kit32PFL4907 Left and right sideWarranty Pixel characteristicsFederal Communications Commission Notice ModificationsConsumer Notice CopyrightVudutm is a trademark of VUDU, Inc Twitter is a trademark of Twitter, IncRegulatory notices Positioning the TVEnvironmental care End of life directivesSupplied accessories FeaturesGet started DTV /TV / CATVSlide the battery cover off the back of the remote control Installing the remote control batteriesAttaching the base Managing cablesPOWER-ON / STANDBY-ON Remote control functionPREV.CH Terminals Control panelPlugging in the AC power cord Connecting the antenna or the cableWireless Initial setupStop SkipPress OK to finish Settings assistant After an initial setup is completedAdjusting volume Switching on your TV and putting it in Standby modeSwitching channels Use your TVEnable or disable RC key forwarding from the Home menu Access the Home menuWatching channels from an external device Lock or unlock your device from the Home menuView photos, play music and watch videos using Dlna Philips Wireless MediaConnectListen to music using Dlna View your pictures using DlnaWatch videos using Dlna Guide to DlnaNet TV Video playback Enjoying vTunerAdd to Favorites Remove from FavoritesAdd to favorite list Internet radio playbackRemove from favorite list Add stations on the vTuner websitePandora operations Logging in to Twitter Using TwitterGuide to Twitter Home screen Viewing tweets on the TVDisplaying Mentions on Twitter Viewing Favorites on TwitterViewing Lists on Twitter Viewing Trends on TwitterSleep timer Using auto modeCreate and use lists of favorite channels For 169 video signal For PC Input signalFor 43 video signal Changing picture formatPicture Jpeg Video Mpeg Music MP3Use more of your TV You must set Home in Location. p Picture Settings assistant Start nowAuto picture Personal Brightness Color Tint SharpnessColor enhancement Off Film modeRed AlignmentAVL Caption settings Child and ratings lock SleeptimerClosed captions Channel lock Start now Channel lock TV ratings lock Movie ratings lockChannel lock Setting TV and movie ratingsChild lock Movie ratings lock TV-MALanguage Change PINCanada English or Canada French ratings Weak channel installation Channel installationInstallation mode Uninstall channelsPreferences Setting your location to homeUse Philips EasyLink StickerDevice list EasyLinkHdmi HDMI-ARCManual network settings Network settings assistantNetwork WPSManually enter your Ssid AutoAuto Router Enter Key NoneConnection test IP configurationPreparing for the software upgrade Return your settings to default valuesChecking your current software version Automatically check for latest software Upgrading the softwareNetflix deactivation Netflix ESNConnecting your devices Connecting devicesSelecting your connection quality HDMI-ARC connection Connecting the TV to the Internet using an Ethernet cableComponent Analog Video Connection Composite Analog Video ConnectionDigital Audio Output Connection Connecting the TV to the Internet using a wireless LANPC connection USB Memory Stick Following video signals can be displayedUseful tips TroubleshootingWhen using the HDMI-DVI No picture or sound Check if the Power is OnConnectors are mounted into the Audio L/R Input jacks Adjusted Picture or Sound You must set Home in Location. pCannot use the wireless Wireless connection is poorCheck the firewall setting of the modem or router Check if your PC runs Philips Wireless MediaConnectInformation MaintenanceGlossary Specifications Contact the Customer Care Center at 1 866 309 WarrantyGPL LicenseNo Warranty Iii How to Apply These Terms to Your New ProgramsPage Page USA How to Apply These Terms to Your New LibrariesAres ExpatLibxml2 LuaXmlrpc Zlib/libpng LicenseFree Type LibJPEG OpenSSLUnicode Original SSLeay LicenseIncluding the GNU Public Licence UNICODE, INC. License Agreement Data Files and Software OpenGLLicense means this document Page Exhibit a XiiKoninklijke Philips Electronics N.V Philips and Philips Shield are used under license
Related manuals
Manual 67 pages 9.61 Kb