Philips 26TA1000/93 setup guide TV Channel Installation, Presentation of the LCD TV

Page 2

TV CHANNEL INSTALLATION

Immediately after unpacking and plugging in your new television, run the auto program function to set up the TV for the broadcast or cable channels available in your area. If you do not run the auto program function to set up the channels , your television may not operate properly.

1

2

3

4

5

Please follow these steps to install TV channels:

Select a TV source via AV button on your remote control.

Press the CURSOR RIGHT button to confi rm.

Press MENU button on your remote control to open the onscreen menu.

Press CURSOR DOWN to move to INSTALL, press CURSOR RIGHT on your remote control to enter INSTALL.

Press CURSOR DOWN to move to AUTO PROGRAM.

Press CURSOR RIGHT to start auto install the TV Channels.

For more detailed explanation of AUTO PROGRAM, please refer to AUTO PROGRAM section on page 5.

MAIN CONTROLS

 

PICTURE

LANGUAGE

 

AUDIO

AUTO PROGRAM

A/CH

FEATURES

MANUAL STORE

 

INSTALL

CHANNEL SETTING

 

 

FACTORY RESET

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INSTALL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LANGUAGE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

AUTO PROGRAM

 

START?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

MANUAL STORE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CHANNEL SETTING

 

 

3

 

 

 

 

 

 

 

5

FACTORY RESET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO STORE

 

 

 

 

 

 

 

 

 

1

PLEASE WAIT

 

 

 

 

 

 

 

 

 

PROG.FOUND

0

 

 

 

 

 

 

 

 

FREQUENCY

MHZ

 

 

 

 

 

 

i +

 

AV

 

 

 

PRESENTATION OF THE LCD TV

1Television Keys

VOLUME + / - : To adjust sound level.

CHANNEL + / - : To select programs.

MENU : To access or close onscreen menu.

2Powersensor button, LED light and infrared

: To switch the TV on or off.

Aim remote control at infrared sensors to activate TV controls.

3Rear connectors

Remove the cable cover to access the connectors at the rear of the LCD TV.

4Bottom connectors

Located at the bottom of the set.

1

2

4

3

2

Image 2
Contents Contents Installing LCD TV on the WallTV Channel Installation Presentation of the LCD TVRemote Control Operation AccessoriesBattery Installation Antenna TV Basic Cable TV ConnectionAuto Program Setting UP Channels Manual Store of TV ChannelCable BOX with RF in / Outputs Cable BOX with Audio / Video OutputsYou can also use the Video and Audio jacks in AV in 2 and AV PC Monitor Connections Digital Satellite Receiver with DVI Connector AV Output