Philips 3135 035 21372 setup guide Operating the Television and Remote Control, Antenna TV

Place the two “AA” size batteries in the remote’s bat- tery case. Ensure that the (+) and (–) ends of the batteries line up correctly with the (+) and (–) inside the case.

Slide the battery cover back into place.

HOOKING UP THE TV

ANTENNA TV

This connection WILL supply stereo sound to the TV.

1 Connect the antenna signal to the ANTENNA IN 75Ω jack on the back of the TV.

NOTE: Refer to the sections on TUNER MODE and AUTO PROGRAM on pages 4 and 5 of this guide. Set TUNER MODE to the ANTENNA option. Run AUTO PROGRAM to store all available cable channels in the TV’s memory.

Antenna Signal

1 Back of TV

ANTENNA IN 75Ω

			HD INPUT-AV 5
			DVI
			HD INPUT-AV 4
			G/Y
			R/Pr
INPUT-AV 1		OUTPUT	INPUT-AV 2
	Y		B/Pb
VIDEO		VIDEO
S-VIDEO			S-VIDEO
L	Pb		L
			V
L		L	L	L
			SYNC
AUDIO	Pr	AUDIO	AUDIO	AUDIO
			H
R		R	R	R

OPERATING THE TELEVISION AND REMOTE CONTROL

TELEVISION

USING THE TV BUTTONS

Should your remote control be lost or broken, you can still change some of the basic picture and sound settings with the

buttons on the TV. Follow the steps below to familiarize yourself with the functions of the TV buttons.

1 Press POWER/STANDBY to turn the TV on (or off). Allow about 10 seconds for the TV to power on.

2 Press the VOL(ume) + or – buttons to decrease or increase the sound level.

Press the VOLUME + and – buttons simultaneously to dis- play the on-screen menu. After the menu appears, use these buttons to enter submenus and make selections or adjust- ments. (Use the CHANNEL buttons to move up and down in the menu or submenus.) Press both VOLUME buttons simultaneously to back out of the on-screen menus.

3 Press SOURCE SELECT to choose from among the sig- nal inputs you have connected to the TV.

4 Press the CHANNEL buttons to select TV channels.

VOLUMECHANNEL

-A +A ? >

MENU

Remote Sensor

Window

HELPFUL HINT

You can press any of the buttons on the front of the TV to turn the TV on, but you must press the Power/Standby button to turn the set off.

SOURCE

SELECT

Power Standby

Button

REMOTE CONTROL

BATTERY USAGE CAUTION

INSTALLING BATTERIES

To load the supplied batteries into the remote, follow these steps.

1 Gently press and hold the indentation on the back of the remote and slide the battery cover off the remote.

2

3

POINTING THE REMOTE

Press the TV mode button on the remote to ensure that the remote sends its commands to the TV. When operating the remote control, point the remote toward the remote sensor win- dow on the TV.

cCHECK IT OUT

You can set up your TV remote control to work with accessory devices such as VCRs, DVD players, and cable converter boxes. See pages 18–23 in the Directions for Use manual.

POWER

			TV	VCR	ACC
		ACC
	VCR	ACTIVE	FREEZE
TV		CONTROL
OK	CH
	PIP	P
	N	U	PICTURE
SWAP	DN	UP
	D
				MENU/
				SELECT

TV MODE

Button

		3
2		3
2			6
1
			6
1		5
4		5	9
			9
4			8
	7		8
				SURFCC
	7		0
		TV/VCR
		A/CH
		A/CH		PIP
			POSITION

To prevent battery leakage that may result in injury to you or dam- age to the remote control:

•Install ALL batteries correctly, + and –, as marked on the unit.

•Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.)

•Remove batteries when the remote control is not used for a long time.

Do not take apart, heat, or put bat- teries in fire.

HELPFUL HINTS

•Be sure to point the remote toward the sensor window on the TV or accessory device you wish to operate.

•Press the correct mode button for the device: TV, VCR, ACC (for accessories other than VCRs).

•Be within about 30 feet (10 meters) of the TV or accessory device you wish to operate.

•Avoid dropping the remote on hard sur- faces.

•Do not use harsh chemicals to clean the remote. Use only a soft, lightly mois- tened cloth.

2